Linus Torvalds [Fri, 5 Dec 2025 01:29:41 +0000 (17:29 -0800)]
Merge tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
Linus Torvalds [Fri, 5 Dec 2025 01:10:08 +0000 (17:10 -0800)]
Merge tag 'efi-next-for-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI updates from Ard Biesheuvel:
"The usual trickle of EFI contributions:
- Parse SMBIOS tables in memory directly on Macbooks that do not
implement the EFI SMBIOS protocol
- Obtain EDID information from the primary display while running in
the EFI stub, and expose it via bootparams on x86 (generic method
is in the works, and will likely land during the next cycle)
- Bring CPER handling for ARM systems up to data with the latest EFI
spec changes
- Various cosmetic changes"
* tag 'efi-next-for-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
docs: efi: add CPER functions to driver-api
efi/cper: align ARM CPER type with UEFI 2.9A/2.10 specs
efi/cper: Add a new helper function to print bitmasks
efi/cper: Adjust infopfx size to accept an extra space
RAS: Report all ARM processor CPER information to userspace
efi/libstub: x86: Store EDID in boot_params
efi/libstub: gop: Add support for reading EDID
efi/libstub: gop: Initialize screen_info in helper function
efi/libstub: gop: Find GOP handle instead of GOP data
efi: Fix trailing whitespace in header file
efi/memattr: Convert efi_memattr_init() return type to void
efi: stmm: fix kernel-doc "bad line" warnings
efi/riscv: Remove the useless failure return message print
efistub/x86: Add fallback for SMBIOS record lookup
- Updates to brcm,bcm2836-l1-intc, brcm,bcm2835-hvs, and bcm2711-hdmi
bindings to fix warnings on BCM2712 platforms
- Drop obsolete db8500-thermal.txt
- Treewide clean-up of extra blank lines and inconsistent quoting
- Ensure all .dtbo targets are applied to a base .dtb
- Speed up dt_binding_check by skipping running validation on empty
examples
DT core:
- Add of_machine_device_match() and of_machine_get_match_data()
helpers and convert users treewide
- Fix bounds checking of address properties in FDT code. Rework the
code to have a single implementation of the bounds checks.
- Rework of_irq_init() to ignore any implicit interrupt-parent (i.e.
in a parent node) on nodes without an interrupt. This matches the
spec description and fixes some RISC-V platforms.
- Avoid a spurious message on overlay removal
- Skip DT kunit tests on RISCV+ACPI"
* tag 'devicetree-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: kbuild: Skip validating empty examples
dt-bindings: interrupt-controller: brcm,bcm2836-l1-intc: Drop interrupt-controller requirement
dt-bindings: display: Fix brcm,bcm2835-hvs bindings for BCM2712
dt-bindings: display: bcm2711-hdmi: Add interrupt details for BCM2712
of: Skip devicetree kunit tests when RISCV+ACPI doesn't populate root node
soc: tegra: Simplify with of_machine_device_match()
soc: qcom: ubwc: Simplify with of_machine_get_match_data()
powercap: dtpm: Simplify with of_machine_get_match_data()
platform: surface: Simplify with of_machine_get_match_data()
irqchip/atmel-aic: Simplify with of_machine_get_match_data()
firmware: qcom: scm: Simplify with of_machine_device_match()
cpuidle: big_little: Simplify with of_machine_device_match()
cpufreq: sun50i: Simplify with of_machine_device_match()
cpufreq: mediatek: Simplify with of_machine_get_match_data()
cpufreq: dt-platdev: Simplify with of_machine_get_match_data()
of: Add wrappers to match root node with OF device ID tables
dt-bindings: eeprom: at25: Add Anvo ANV32C81W
of/reserved_mem: Simplify the logic of __reserved_mem_alloc_size()
of/reserved_mem: Simplify the logic of fdt_scan_reserved_mem_reg_nodes()
of/reserved_mem: Simplify the logic of __reserved_mem_reserve_reg()
...
Linus Torvalds [Thu, 4 Dec 2025 23:44:48 +0000 (15:44 -0800)]
Merge tag 'hid-for-linus-2025120201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- Proper mapping of HID_GD_Z to ABS_DISTANCE for stylus/pen types of
devices (Ping Cheng)
- Power management/hibernation improvements in intel-ish (Zhang Lixu)
- Improved support for several Logitech devices, e.g. G Pro X
Superlight 2, new iteration of Lighspeed receiver, G13, G510 (Nathan
Rossi, Mavroudis Chatzilazaridis, Leo L Schwab, Hans de Goede)
- Support for UcLogic XP-PEN Artist 24 Pro (Joshua Goins)
- WinWing Orion2 throttle support improvement (Ivan Gorinov)
- other assorted small fixes and device ID additions
* tag 'hid-for-linus-2025120201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (37 commits)
drivers: hid: renegotiate resolution multipliers with device after reset
HID: evision: Fix Report Descriptor for Evision Wireless Receiver 320f:226f
HID: logitech-dj: Fix probe failure when used with KVM
HID: logitech-dj: Remove duplicate error logging
HID: logitech-dj: Add support for G Pro X Superlight 2 receiver
selftests/hid-tablet: add ABS_DISTANCE test for stylus/pen
HID: input: map HID_GD_Z to ABS_DISTANCE for stylus/pen
HID: bpf: fix typo in HID usage table
HID: bpf: add the Huion Kamvas 27 Pro
HID: bpf: add heuristics to the Huion Inspiroy 2S eraser button
HID: bpf: Add support for XP-Pen Deco02
HID: bpf: Add support for the XP-Pen Deco 01 V3
HID: bpf: Add support for the Waltop Batteryless Tablet
HID: bpf: Add fixup for Logitech SpaceNavigator variants
HID: bpf: support for Huion Kamvas 16 Gen 3
HID: bpf: add support for Huion Kamvas 13 (Gen 3) (model GS1333)
HID: bpf: Add support for the Inspiroy 2M
Documentation: hid-alps: Format DataByte* subsection headings
Documentation: hid-alps: Fix packet format section headings
HID: nintendo: add WQ_PERCPU to alloc_workqueue users
...
Linus Torvalds [Thu, 4 Dec 2025 23:29:27 +0000 (15:29 -0800)]
Merge tag 'backlight-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Additions:
- Add support for Awinic AW99706 backlight driver
Fixes:
- Add GPIOLIB dependency to backlight ktd2801 driver
- Add devlink to LED Backlight's supplier LEDs to enforce correct
removal order and prevent NULL pointer dereferences
- Fix kernel-doc warnings in lp855x.h
Removals:
- Do not include <linux/fb.h> in backlight.h
- Fix unused function warnings from suspend/resume ops in aw99706.c
by switching to DEFINE_SIMPLE_DEV_PM_OPS and using pm_ptr()
* tag 'backlight-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: aw99706: Fix unused function warnings from suspend/resume ops
backlight: lp855x: Fix lp855x.h kernel-doc warnings
dt-bindings: leds: backlight: Add Awinic AW99706 backlight
backlight: aw99706: Add support for Awinic AW99706 backlight
backlight: led-bl: Add devlink to supplier LEDs
backlight: ktd2801: Depend on GPIOLIB
backlight: Do not include <linux/fb.h> in header file
Linus Torvalds [Thu, 4 Dec 2025 23:25:19 +0000 (15:25 -0800)]
Merge tag 'leds-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Updates:
- Add optional GPIO enable pin support to PWM LED driver
Fixes:
- Allow LED module 0 to be added to module bank in lp50xx driver
- Fix upboard LED driver module alias to ensure proper auto-loading
- Update LP5009 to support 3 modules for a total of 9 LEDs
- Skip LEDs without color components in cros_ec driver instead of
failing probe
- Fix GPIO descriptor leaks in netxbig error paths by releasing
acquired GPIOs
- Allow LED_COLOR_ID_MULTI in qcom-lpg driver for greater flexibility
- Enable LP55XX common LED use without FW_LOADER_USER_HELPER
- Ensure lp50xx chip is enabled before any I2C communication
Cleanups:
- Use fwnode_for_each_child_node() instead of
fwnode_for_each_available_child_node() in LED drivers
- Use device_get_next_child_node() instead of
fwnode_get_next_available_child_node() in LED flash drivers
- Replace sprintf() with sysfs_emit() in sysfs show functions for
improved bounds checking
- Replace system_wq() with system_percpu_wq() in the input event
trigger
- Reorder include files to alphabetic order in the PWM LED driver
- Do not enable TRILED in qcom-lpg when configuring PWM
- Drop duplicate LEDS_EXPRESSWIRE config from Kconfig
Removals:
- Remove arcxcnn_bl.txt Device Tree binding documentation
Devicetree bindings:
- Convert ArcticSand arc2c0608 LED driver binding to DT Schema
- Add default-brightness property to common LED binding
- Add enable-gpios property to PWM LED binding
- Add PM7550 to qcom,spmi-flash-led compatible
- Explain standalone PWM usage in qcom-lpg binding"
* tag 'leds-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (21 commits)
leds: rgb: leds-qcom-lpg: Don't enable TRILED when configuring PWM
dt-bindings: leds: qcom-lpg: Explain standalone PWM usage
leds: rgb: leds-qcom-lpg: Allow LED_COLOR_ID_MULTI
leds: pwm: Reorder include files to alphabetic order
leds: pwm: Add optional GPIO enable pin support
dt-bindings: leds: pwm: Add enable-gpios property
leds: trigger: Replace use of system_wq() with system_percpu_wq()
leds: led-class: Replace sprintf() with sysfs_emit() in sysfs show functions
dt-bindings: leds: qcom,spmi-flash-led: Add PM7550
leds: netxbig: Fix GPIO descriptor leak in error paths
leds: leds-lp50xx: Enable chip before any communication
leds: Drop duplicate LEDS_EXPRESSWIRE config
leds: leds-cros_ec: Skip LEDs without color components
leds: leds-lp50xx: LP5009 supports 3 modules for a total of 9 LEDs
leds: upboard: Fix module alias
leds: leds-lp50xx: Allow LED 0 to be added to module bank
leds: lp55xx_common: Enable use without FW_LOADER_USER_HELPER
dt-bindings: leds: Add default-brightness property to common.yaml
leds: flash: Use fwnode_get_next_child_node() instead
leds: Use fwnode_for_each_child_node() instead
...
Linus Torvalds [Thu, 4 Dec 2025 23:18:33 +0000 (15:18 -0800)]
Merge tag 'mfd-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Updates:
- Add Core, Regulator, Onkey and Battery Charger support for the NXP
PF1550 Power Management IC (PMIC)
- Introduce __SMC_KEY macro to fix GCC 15.2.1 errors in macsmc
- Add board definitions for TQMxCU1-HPCM and TQMxCU2-HPCM to the
tqmx86 driver
- Add support for Broadcom BCM2712 SoC to the bcm2835-pm driver
- Hook up the qnap-mcu-eeprom sub-device to qnap-mcu
Fixes:
- Enable compile testing for the Altera SOCFPGA System Manager driver
- Fix device reference leak in altr_sysmgr_regmap_lookup_by_phandle()
- Reserve the unused second I2C address for DA9063 to prevent
userspace interference
- Fix resource leak in da9055_device_init() by calling
regmap_del_irq_chip() in the error path
- Fix potential IRQ chip conflict when probing multiple MAX77620
devices by using devm_kmemdup for regmap_irq_chip
- Return -EPROBE_DEFER when a syscon devuice is not found to allow
deferred probing
- Update email address for the PF1550 PMIC driver in MAINTAINERS
- Correct file entry for PF1550 MFD driver in MAINTAINERS from
pfd1550.h to pf1550.h
- Calculate checksum on the actual number of received bytes in
qnap-mcu for error messages
- Use -EPROTO instead of -EIO for checksum errors in qnap-mcu
- Add proper error handling for command errors (e.g., "@8", "@9") in
qnap-mcu
- Fix missing irq_domain_remove() in error path of
mt63{58,97}_irq_init()
Cleanups:
- Mark SMC write buffer arguments as const in apple_smc_write(),
apple_smc_rw(), and apple_smc_write_atomic()
- Simplify the error handling path in da9055_device_init() by
removing a redundant mfd_remove_devices() call
- Use regmap_reg_range() and a real one-element array for
pmic_status_range in rohm-bd718x7 for cleaner initialization
- Remove select I2C_K1 from MFD_SPACEMIT_P1 to avoid build failures
when I2C_K1's dependencies are disabled
- Remove unneeded semicolon from ls2k_bmc_recover_pci_data()
- Drop OF dependency for MFD_MAX5970 in Kconfig to allow wider
compile testing and non-OF systems
- Make OF ID table style consistent in simple-mfd-i2c driver
- Update header inclusions in simple-mfd-i2c to follow IWYU (Include
What You Use) principle
- Move checksum verification logic to a separate function in qnap-mcu
- Use chained IRQs for S2MPG10 in the Samsung SEC driver to simplify
interrupt handling
- Drop a stray semicolon from sec-irq.c
Removals:
- Remove the unused TI WL1273 FM radio core driver
- Remove the unused wl1273-core.h header and tidy up its reference in
documentation
Device tree bindings:
- Add Device Tree binding for the NXP PF1550 PMIC
- Add missing GPIO pins and supply properties to the Silergy SY7636A
PMIC binding
- Add interrupt-controller property to the Maxim MAX77705 binding for
sub-device interrupt source determination
- Add Device Tree binding for the Renesas R2A11302FT PMIC
- Allow the wakeup-source property in the Dialog DA9063 binding
- Make interrupt-related properties optional in the TI TPS65910 PMIC
binding
- Document the Qualcomm PMIV0104 PMIC compatible string
- Document the Qualcomm PM7550 PMIC compatible string
- Enable power button subnode for TWL603x in the TI TWL binding
- Convert the Dialog DA9052/53 I2C binding from .txt to .yaml format,
including compatible string fallback and interrupt properties
- Document control-scb and sysreg-scb syscons on pic64gx with
fallback compatibles
- Document sama7g5-sfrbu and sama7d65-sfrbu syscons with fallback to
atmel,sama5d2-sfrbu
- Fix LEDs node schema in fsl,mc13xxx binding by adding led@ child
nodes and missing properties
- Add mt7981-topmisc compatible string to the syscon binding"
* tag 'mfd-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
mfd: sec: Drop a stray semicolon
mfd: qnap-mcu: Hook up the EEPROM sub-device
dt-bindings: mfd: syscon: Add mt7981-topmisc
dt-bindings: mfd: fsl,mc13xxx: Fix LEDs node schema
mfd: mt6358-irq: Fix missing irq_domain_remove() in error path
mfd: mt6397-irq: Fix missing irq_domain_remove() in error path
dt-bindings: mfd: Document syscons falling back to atmel,sama5d2-sfrbu
dt-bindings: mfd: Document control-scb and sysreg-scb on pic64gx
dt-bindings: mfd: Convert dlg,da9052-i2c.txt to yaml format
mfd: sec: Use chained IRQs for s2mpg10
mfd: qnap-mcu: Add proper error handling for command errors
mfd: qnap-mcu: Move checksum verification to its own function
mfd: qnap-mcu: Use EPROTO in stead of EIO on checksum errors
mfd: qnap-mcu: Calculate the checksum on the actual number of bytes received
mfd: simple-mfd-i2c: Don't use "proxy" headers
mfd: simple-mfd-i2c: Make ID table style consistent
mfd: Kconfig: Drop OF dependency on MFD_MAX5970
mfd: ls2kbmc: Remove unneeded semicolon from ls2k_bmc_recover_pci_data()
dt-bindings: mfd: twl: Enable power button also for TWL603X
MAINTAINERS: Adjust file entry in NXP PF1550 PMIC MFD DRIVER
...
Linus Torvalds [Thu, 4 Dec 2025 22:10:16 +0000 (14:10 -0800)]
Merge tag 'mmc-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Allow more host caps to be modified through debugfs
- Skip to set the default 200mA SD current limit
MMC host:
- Convert a few more DT bindings to the DT schema
- dw_mmc: Add Shawn Lin as co-maintainer for the dw_mmc drivers
- dw_mmc-rockchip:
- Add memory clock auto-gating support
- Add support for the RK3506 variant
- meson-mx-sdio:
- Ignore disabled "mmc-slot" child-nodes
- Refactoring and general code improvements
- renesas_sdhi:
- Enable bigger data ports where available
- Manage reset in probe and during system-wide suspend/resume
- sdhci-brcmstb:
- Add support for the BCM72116 and BCM74371 variants
- Save/restore registers during system-wide suspend/resume
- sdhci-msm:
- Add support for the sm8750 and the Kaanapali variants
- Avoid early clock doubling during HS400 transition
- sdhci-of-dwcmshc:
- Add command queue support for Rockchip SOCs
- Add support for the Eswin EIC7700 variant"
* tag 'mmc-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (40 commits)
mmc: sdhci-of-dwcmshc: reduce CIT for better performance
mmc: sdhci-of-dwcmshc: Disable internal clock auto gate for Rockchip SOCs
mmc: sdhci-msm: Avoid early clock doubling during HS400 transition
MAINTAINERS: Add Shawn Lin as co-maintainer for dw_mmc drivers
mmc: sdhci-of-dwcmshc: Fix command queue support for RK3576
mmc: renesas_sdhi: Add suspend/resume hooks
mmc: renesas_sdhi: Switch to SYSTEM_SLEEP_PM_OPS()/RUNTIME_PM_OPS() and pm_ptr()
mmc: renesas_sdhi: Deassert the reset signal on probe
dt-bindings: mmc: am654: Simplify dma-coherent property
mmc: meson-mx-sdio: Ignore disabled "mmc-slot" child-nodes
mmc: meson-mx-sdio: Fix indentation in meson_mx_mmc_irq_thread()
mmc: meson-mx-sdio: Use dev_err_probe() where appropriate
mmc: meson-mx-sdio: Use devm_mmc_alloc_host() helper
mmc: meson-mx-sdio: Refactor internal clock initialization
mmc: meson-mx-sdio: Use devm_clk_get_enabled()
mmc: meson-mx-sdio: Switch to regmap for register access
mmc: core: add WQ_PERCPU to alloc_workqueue users
mmc: dw_mmc-rockchip: Add memory clock auto-gating support
mmc: omap: add WQ_PERCPU to alloc_workqueue users
mmc: mtk-sd: replace use of system_wq with system_percpu_wq
...
Linus Torvalds [Thu, 4 Dec 2025 21:50:39 +0000 (13:50 -0800)]
Merge tag 'pmdomain-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
- Allow power-off for out-of-band wakeup-capable devices
- Drop the redundant call to dev_pm_domain_detach() for the amba bus
- Extend the genpd governor for CPUs to account for IPIs
pmdomain providers:
- bcm: Add support for BCM2712
- mediatek: Add support for MFlexGraphics power domains
- mediatek: Add support for MT8196 power domains
- qcom: Add RPMh power domain support for Kaanapali
- rockchip: Add support for RV1126B
pmdomain consumers:
- usb: dwc3: Enable out of band wakeup for i.MX95
- usb: chipidea: Enable out of band wakeup for i.MX95"
* tag 'pmdomain-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (26 commits)
pmdomain: Extend the genpd governor for CPUs to account for IPIs
smp: Introduce a helper function to check for pending IPIs
pmdomain: mediatek: convert from clk round_rate() to determine_rate()
amba: bus: Drop dev_pm_domain_detach() call
pmdomain: bcm: bcm2835-power: Prepare to support BCM2712
pmdomain: mediatek: mtk-mfg: select MAILBOX in Kconfig
pmdomain: mediatek: Add support for MFlexGraphics
pmdomain: mediatek: Fix build-errors
cpuidle: psci: Replace deprecated strcpy in psci_idle_init_cpu
pmdomain: rockchip: Add support for RV1126B
pmdomain: mediatek: Add support for MT8196 HFRPSYS power domains
pmdomain: mediatek: Add support for MT8196 SCPSYS power domains
pmdomain: mediatek: Add support for secure HWCCF infra power on
pmdomain: mediatek: Add support for Hardware Voter power domains
pmdomain: qcom: rpmhpd: Add RPMh power domain support for Kaanapali
usb: dwc3: imx8mp: Set out of band wakeup for i.MX95
usb: chipidea: ci_hdrc_imx: Set out of band wakeup for i.MX95
usb: chipidea: core: detach power domain for ci_hdrc platform device
pmdomain: core: Allow power-off for out-of-band wakeup-capable devices
PM: wakeup: Add out-of-band system wakeup support for devices
...
Linus Torvalds [Thu, 4 Dec 2025 20:33:38 +0000 (12:33 -0800)]
Merge tag 'gpio-updates-for-v6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There's one new driver, lots of various updates to existing ones, some
refactoring support for new models and misc tweaks and fixes.
The biggest new feature in GPIO core is adding support for managed,
enable-counted sharing of GPIO pins, something that - until now - was
only hacked around with the GPIOD_FLAGS_BIT_NONEXCLUSIVE request flag
which basically allowed drivers to "fight it out" for the descriptor
and provided no synchronization. It was enabled on Qualcomm platforms
(and thus is enabled on arm64 defconfig) and I plan on removing
GPIOD_FLAGS_BIT_NONEXCLUSIVE once all drivers using it are switched to
the new mechanism.
GPIO core:
- add proper support for shared GPIOs that's aiming to replace the
current sharing mechanism (which provides no synchronization ot
enable counting) and enable it for Qualcomm platforms
- improve the software node GPIO lookup by using the fwnode
representation instead of the software node's name which was prone
to bugs (GPIO controllers don't have to use the software node's
name as their kernel label)
- remove the last user of legacy-of-mm-gpiochip.h and drop the header
- move closer to removing the legacy gpio_request_one() routine
- rename some symbols for consistency
- shrink GPIO printk() helpers by reusing existing code
- remove some redundant kernel messages
- use min() instead of min_t() in GPIO ACPI code
- use system_percpu_wq instead of system_wq in GPIO character device
code
New drivers:
- add a driver for the QIXIS FPGA GPIO controller
Driver improvements:
- use modernized variants of power management macros across a wide
array of drivers in order to avoid having to use the __maybe_unused
attribute
- convert gpio-elkhartlake and reset-gpio to using the auxiliary bus
instead of the platform bus as they are not really described in
firmware
- use lock guards and update symbol prefixes in gpio-mmio
- support the bryx radio interface kit in gpio-mpsse + refactor the
driver
- use software nodes for configuring the reset-gpio driver, including
setting up the reference to the shared "reset" pin
- check and propagate the return value of gpiod_set_value() to
user-space in gpio-virtuser (this was previously not possible as
this function returned void)
- extend the gpio-regmap helper with more features (bypass cache for
aliased inputs, force writes for aliased data registers, add a new
configuration parameter)
- remove unneeded includes from gpio-aspeed and gpio-latch
- add support for Tegra410 to gpio-tegra186
- replace PCI-specific PM with generic device-level PM in gpio-bt8xx
- use dynamic GPIO range allocation in gpio-loongson-64bit
- improve handling of level-triggered interrupts in gpio-pca953x
- add suspend/resume support to gpio-fxl6408
- add support for more models to gpio-menz127
- optimize gpio-mvebu interrupt handling by avoiding unnecessary
calls to mvebu_gpio_irq_handler()
- make locking more consistent in gpio-grgpio
Device-tree bindings:
- document new NXP and Microchip models
Documentation:
- add a comprehensive compatibility and feature list for
gpio-pca953x, which is a great addition as it's probably the most
commonly used GPIO expander driver
- kernel-doc tweaks
Late fixes:
- use BYTE_CTRL_MODE for 2K2000/3000 models in gpio-loongson"
* tag 'gpio-updates-for-v6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (80 commits)
gpio: loongson: Switch 2K2000/3000 GPIO to BYTE_CTRL_MODE
gpio: regmap: fix kernel-doc notation
gpio: shared: fix a deadlock
gpio: shared-proxy: set suppress_bind_attrs
gpio: shared: ignore GPIO hogs when traversing the device tree
gpio: shared: ignore special __symbols__ node when traversing device tree
gpio: shared: handle the reset-gpios corner case
gpio: zynq: Use modern PM macros
gpio: xilinx: Use modern PM macros
gpio: xgene: Use modern PM macros
gpio: uniphier: Use modern PM macros
gpio: tqmx86: Use modern PM macros
gpio: pch: Use modern PM macros
gpio: omap: Use modern PM macros
gpio: msc313: Use modern PM macros
gpio: mlxbf2: Use modern PM macros
gpio: ml-ioh: Use modern PM macros
gpio: pl061: Use modern PM macros
gpio: htc-egpio: Use modern PM macros
gpio: brcmstb: Use modern PM macros
...
Linus Torvalds [Thu, 4 Dec 2025 20:26:36 +0000 (12:26 -0800)]
Merge tag 'firewire-updates-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Takashi Sakamoto:
"This includes two changes for core functions, which affects all use
cases of this subsystem:
- Handle per-device interoperability quirks
Some devices have quirks affecting interoperability. To identify
such quirks at an early stages of device detection, the step for
reading the configuration ROM contents has been changed. As a side
effect, the entire detection process is now performed at the basic
transaction speed (S100), without a trial to probe higher
supported speeds.
With this change, the following devices should now work with fewer
issues:
- TASCAM FW-1884, FW-1804, and FW-1082
- MOTU Audio Express
- Safer removals of host card
There was a race condition between host card removal and handling
of bus reset events in the workqueue. This appears to be a long
standing issue, and recent changes to use more workqueues escalate
it.
To solve it, a new callback has been added to the 1394 OHCI PCI
driver to unregister the interrupt sources and wait for workqueue
completions when removing a card instance"
* tag 'firewire-updates-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: core: abort pending transactions at card removal
firewire: core: add WQ_UNBOUND to alloc_workqueue users
firewire: core: clear sources of hardware interrupt at card removal
firewire: core: code refactoring to find and pop transaction entry
firewire: core: code refactoring to remove transaction entry
firewire: core: use cleanup function to release cached configuration ROM
ALSA: firewire-tascam: reserve resources for transferred isochronous packets at S400
firewire: core: handle device quirk of TASCAM FW-1884/FW-1804/FW-1082
firewire: core: determine transaction speed after detecting quirks
firewire: core: code refactoring to compute transaction speed
firewire: core: handle device quirk of MOTU Audio Express
firewire: core: detect device quirk when reading configuration ROM
Linus Torvalds [Thu, 4 Dec 2025 20:19:49 +0000 (12:19 -0800)]
Merge tag 'hwmon-for-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Apple Silicon SMC
- TSC1641 I2C power monitor
- MPS MP9945
- MAX17616
- MP2925 and MP2929
Added support for new devices to existing drivers:
- dell-smm: Add Dell G5 5505 to fan control whitelist
- aspeed-g6-pwm-tach: Support for AST2700
- asus-ec-sensors: Support for ROG STRIX X470-I GAMING, ROG STRIX
X870-F GAMING WIFI, ROG STRIX X870E-H GAMING WIFI7, and Pro WS
TRX50-SAGE WIFI
- k10temp: Support for AMD Steam Deck APU ID
- pmbus/isl68137: Support for raa229141
- aht10: Support for dht20
- adt7410: Support for ADT7422
- peci: Support for Intel Emerald Rapids
- nct6775: Support for ASUS ROG STRIX X870E-H GAMING WIFI7
- pmbus/max34440: Support for ADPM12200
- ntc-thermistor: Support for Murata ncp18wm474
Infrastructure updates:
- Utilize subsystem locking in various drivers
- ltc4282, ltc2947: Use the new energy64 attribute
Bug fixes:
- Various drivers: Fixes to avoid TOCTOU, mostly in macro functions
evaluating parameters multiple times, as well as missing locks
- max6697: Fix regmap leak on probe failure
- sy7636a: Fix regulator_enable resource leak on error path
- asus-ec-sensors: Correct Pro WS TRX50-SAGE WIFI entry
Other changes and improvements:
- w83781d, lm78: Drop REALLY_SLOW_IO
- Fix broken datasheet links in various drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (110 commits)
hwmon: (dell-smm) Add Dell G5 5505 to fan control whitelist
hwmon: (max16065) Use local variable to avoid TOCTOU
hwmon: (w83l786ng) Convert macros to functions to avoid TOCTOU
hwmon: (max6697) fix regmap leak on probe failure
hwmon/w83781d: Drop REALLY_SLOW_IO setting
hwmon/lm78: Drop REALLY_SLOW_IO setting
hwmon: sy7636a: Fix regulator_enable resource leak on error path
hwmon: (adm1026) Convert macros to functions to avoid TOCTOU
hwmon: (adm1029) Add locking to avoid TOCTOU
hwmon: (lm87) Convert macros to functions to avoid TOCTOU
hwmon: (asus-ec-sensors) correct Pro WS TRX50-SAGE WIFI entry
hwmon: (vt8231) Convert macros to functions to avoid TOCTOU
hwmon: (emc2103) Add locking to avoid TOCTOU
hwmon: (aspeed-g6-pwm-tach): Add AST2700 compatible string
dt-bindings: hwmon: Add AST2700 compatible
hwmon: (asus-ec-sensors) add ROG STRIX X470-I GAMING
hwmon: (vt1211) Convert macros to functions to avoid TOCTOU
hwmon: (k10temp) Add AMD Steam Deck APU ID
hwmon: Add Apple Silicon SMC hwmon driver
Documentation/hwmon: Fix broken datasheet links for zl6100
...
Linus Torvalds [Thu, 4 Dec 2025 19:37:13 +0000 (11:37 -0800)]
Merge tag 'gnss-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss
Pull GNSS updates from Johan Hovold:
- add support for claiming and deasserting the safeboot pin found on
recent u-blox receivers
- fix timepulse pin description in the devicetree binding
... and some related binding updates
* tag 'gnss-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss:
dt-bindings: gnss: fix timepulse description
dt-bindings: gnss: u-blox: use lowercase company name
dt-bindings: gnss: u-blox: use open-drain reset and safeboot in example
gnss: ubx: add support for the safeboot gpio
dt-bindings: gnss: u-blox: add safeboot gpio
Linus Torvalds [Thu, 4 Dec 2025 19:24:24 +0000 (11:24 -0800)]
Merge tag 'spi-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release is almost entirely new drivers, with a couple of small
changes in generic code.
The biggest individual update is a rename of the existing Microchip
driver and the addition of a new driver for the silicon SPI controller
in their PolarFire SoCs. The overlap between the soft IP supported by
the current driver and this new one is regrettably all in the IP and
not in the register interface offered to software.
- Add a time offset parameter for offloads, allowing them to be
defined in relation to each other. This is useful for IIO type
applcations where you trigger an operation then read the result
after a delay.
- Add a tracepoint for flash exec_ops, bringing the flash support
more in line with the debuggability of vanilla SPI.
- Support for Airoha EN7523, Arduino MCUs, Aspeed AST2700, Microchip
PolarFire SPI controllers, NXP i.MX51 ECSPI target mode, Qualcomm
IPQ5414 and IPQ5332, Renesas RZ/T2H, RZ/V2N and RZ/2NH and SpacemiT
K1 QuadSPI.
There's also a small set of ASoC cleanups that I mistakenly applied to
the SPI tree and then put more stuff on top of before it was brought
to my attention, sorry about that"
* tag 'spi-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (80 commits)
spi: microchip-core: Refactor FIFO read and write handlers
spi: ch341: fix out-of-bounds memory access in ch341_transfer_one
spi: microchip-core: Remove unneeded PM related macro
spi: microchip-core: Use SPI_MODE_X_MASK
spi: microchip-core: Utilise temporary variable for struct device
spi: microchip-core: Replace dead code (-ENOMEM error message)
spi: microchip-core: use min() instead of min_t()
spi: dt-bindings: airoha: add compatible for EN7523
spi: airoha-snfi: en7523: workaround flash damaging if UART_TXD was short to GND
spi: dt-bindings: renesas,rzv2h-rspi: Document RZ/V2N SoC support
spi: dt-bindings: renesas,rzv2h-rspi: Document RZ/V2N SoC support
spi: microchip: Enable compile-testing for FPGA SPI controllers
spi: Fix potential uninitialized variable in probe()
spi: rzv2h-rspi: add support for RZ/T2H and RZ/N2H
spi: dt-bindings: renesas,rzv2h-rspi: document RZ/T2H and RZ/N2H
spi: rzv2h-rspi: add support for loopback mode
spi: rzv2h-rspi: add support for variable transfer clock
spi: rzv2h-rspi: add support for using PCLK for transfer clock
spi: rzv2h-rspi: make transfer clock rate finding chip-specific
spi: rzv2h-rspi: avoid recomputing transfer frequency
...
Linus Torvalds [Thu, 4 Dec 2025 19:20:29 +0000 (11:20 -0800)]
Merge tag 'regulator-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This is a relatively busy release for the regulator API, as well as a
good collection of new drivers we've got a little bit of core work and
a bunch of cleanup throughout the subsystem:
- Support for propagating undervoltage events to child regulators
- Undo enables done on supplies when setting enabling regulators via
constraints fails
- Pull in some gpiolib changes adding support for shared GPIOs to the
gpiolib core, using them to replace the open coded variant of this
that we've had in the regulator API for a long time
- Support for Fitipower FP9931 and JD9330, Mediatek MT6316, MT6363
and MT6373, NXP PF1550 and Qualcomm PMH01XX and PMCX0102
The PF1550 support was originally going to go via the MFD tree but
Krzysztof's cleanup work overlapped with it so I pulled in Lee's
signed tag with support for the device"
* tag 'regulator-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (50 commits)
regulator: fp9931: Fix spelling mistake "failid" -> "failed"
regulator: core: Protect regulator_supply_alias_list with regulator_list_mutex
regulator: pf9453: Constify pointers to 'regulator_desc' wrap struct
regulator: pca9450: Constify pointers to 'regulator_desc' wrap struct
regulator: mt6358: Constify pointers to 'regulator_desc' wrap struct
regulator: bd96801: Constify pointers to 'regulator_desc' wrap struct
regulator: bd718x7: Constify pointers to 'regulator_desc' wrap struct
regulator: bd71828: Constify pointers to 'regulator_desc' wrap struct
regulator: bd71815: Constify pointers to 'regulator_desc' wrap struct
regulator: Use container_of_const() when all types are const
regulator: pca9450: Fix error code in probe()
regulator: qcomm-labibb: replace use of system_wq with system_dfl_wq
regulator: Add FP9931/JD9930 driver
dt-bindings: regulator: Add Fitipower FP9931/JD9930
dt-bindings: vendor-prefixes: Add Fitipower
regulator: make the subsystem aware of shared GPIOs
regulator: renesas-usb-vbus-regulator: Remove unused headers
regulator: pca9450: Add support for setting debounce settings
regulator: dt-bindings: pca9540: add debounce timer configuration
regulator: core: disable supply if enabling main regulator fails
...
Linus Torvalds [Thu, 4 Dec 2025 19:16:44 +0000 (11:16 -0800)]
Merge tag 'regmap-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Another small update for regmap, we have one new feature plus a little
bit of cleanup:
- Support for sparseness information in the flat cache, allowing
users that really need the performance properties it provides to
benefit from the interface and startup time improvements that
sparsness provides without needing to go all the way to a more
fancy data structure
- Cleanup work from Andy Shevchenko, refactoring the cache interface
in preparation for some future stuff he's working on"
* tag 'regmap-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: sdw-mbq: Reorder regmap_mbq_context struct for better packing
regmap: i3c: Use ARRAY_SIZE()
regcache: maple: Split ->populate() from ->init()
regcache: flat: Split ->populate() from ->init()
regcache: flat: Remove unneeded check and error message for -ENOMEM
regcache: rbtree: Split ->populate() from ->init()
regcache: Add ->populate() callback to separate from ->init()
regmap: warn users about uninitialized flat cache
regmap: add flat cache with sparse validity
Linus Torvalds [Thu, 4 Dec 2025 19:07:46 +0000 (11:07 -0800)]
Merge tag 'mtd/for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core MTD changes:
- We must ignore error -ENOENT from parsers on subpartitions which is
a legitimate return value
- PM support is added to the intel-dg driver
Raw NAND changes:
- The major change in this is the support for the Allwinner H616 NAND
controller, which lead to numerous changes and cleanups in the
driver.
- Another notable change in this driver is the use of field_get() and
field_prep(), but since the global support for this helpers is
going to be merged in the same release as we start using these
helpers, we undefine them in the first place to avoid warnings.
- Marvell drivers layout handling changes have also landed, they fix
previous definitions and abuses that have been made previously,
which implied to relax the ECC parameters validation in the core a
bit.
- The Cadence NAND controller driver gets NV-DDR interface support.
SPI NAND changes:
- Support for FudanMicro FM25S01BI3 and ESMT F50L1G41LC is added.
SPI NOR changes:
- Fix SMPT parsing for S25FS-S flash family. They report variable
dummy cycles for reads. This results in the default of 0 being
used. This works for other Infineon chips, but not for the S25FS-S
family. They need 8 dummy cycles. Add fixup hooks to specify that.
Also add fixup hooks to fix incorrect map ID data in SFDP.
- Add support for a bunch of Winbond flashes. Their block protection
information is not discoverable, so they need to have an entry in
the flash tables to describe that.
- Some cleanups for Micron flash support.
- Add support for Micron mt35xu01gbba.
- Some SPI controllers like the Intel one on the PCI bus do not
support the read CR opcode (0x35). Do not use the opcode if the
controller does not support it.
Aside from these main changes, there is the usual load of API updates,
kdoc fixes, potential memory leaks fixes, etc"
* tag 'mtd/for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (51 commits)
mtd: sm_ftl: Fix typo in comment in sm_read_lba
mtd: sm_ftl: Replace deprecated strncpy with sysfs_emit in sm_attr_show
mtd: lpddr_cmds: fix signed shifts in lpddr_cmds
mtd: docg3: fix kernel-doc warnings
mtd: spinand: add support for FudanMicro FM25S01BI3
mtd: rawnand: renesas: Handle devm_pm_runtime_enable() errors
mtd: nand: realtek-ecc: Fix Kconfig dependencies
mtd: rawnand: sunxi: #undef field_{get,prep}() before local definition
mailmap: update Pratyush Yadav's email address
mtd: spi-nor: core: Check read CR support
mtd: spi-nor: micron-st: add TODO for fixing mt35xu02gcba
mtd: spi-nor: micron-st: add mt35xu01gbba support
mtd: spi-nor: micron-st: use SFDP of mt35xu512aba
mtd: spi-nor: micron-st: move set_octal_dtr to late_init()
mtd: spi-nor: micron-st: rename the die_late_init functions
mtd: spinand: esmt: add support for F50L1G41LC
mtd: rawnand: lpc32xx_slc: Convert to use devm_gpiod_get_optional()
mtd: mtdpart: ignore error -ENOENT from parsers on subpartitions
mtd: maps: pcmciamtd: fix potential memory leak in pcmciamtd_detach()
mtd: spi-nor: spansion: SMPT fixups for S25FS-S
...
Linus Torvalds [Thu, 4 Dec 2025 19:04:38 +0000 (11:04 -0800)]
Merge tag 'pwm/for-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm updates from Uwe Kleine-König:
"In addition to the usual mix of core cleanups, driver changes, minor
fixes and device tree updates the highlight this cycle is Rust support
for the core and a first Rust driver both provided by Michal
Wilczynski.
* tag 'pwm/for-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux: (22 commits)
pwm: rzg2l-gpt: Allow checking period_tick cache value only if sibling channel is enabled
pwm: bcm2835: Make sure the channel is enabled after pwm_request()
pwm: mediatek: Make use of struct_size macro
pwm: mediatek: Remove unneeded semicolon
pwm: airoha: Add support for EN7581 SoC
pwm: mediatek: Convert to waveform API
pwm: max7360: Clean MAX7360 code
pwm: Drop unused function pwm_apply_args()
pwm: Use %u to printf unsigned int pwm_chip::npwm and pwm_chip::id
pwm: Simplify printf to emit chip->npwm in $debugfs/pwm
pwm: th1520: Use module_pwm_platform_driver! macro
pwm: th1520: Fix clippy warning for redundant struct field init
pwm: Fix Rust formatting
dt-bindings: pwm: thead: Add T-HEAD TH1520 PWM controller
pwm: Add Rust driver for T-HEAD TH1520 SoC
rust: pwm: Fix broken intra-doc link
rust: pwm: Drop wrapping of PWM polarity and state
rust: pwm: Add module_pwm_platform_driver! macro
rust: pwm: Add complete abstraction layer
rust: pwm: Add Kconfig and basic data structures
...
Linus Torvalds [Thu, 4 Dec 2025 18:08:40 +0000 (10:08 -0800)]
Merge tag 'sound-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The majority of changes at this time were about ASoC with a lot of
code refactoring works. From the functionality POV, there isn't much
to see, but we have a wide range of device-specific fixes and updates.
Here are some highlights:
- Continued ASoC API cleanup work, spanned over many files
- Added a SoundWire SCDA generic class driver with regmap support
- Enhancements and fixes for Cirrus, Intel, Maxim and Qualcomm.
- Support for ASoC Allwinner A523, Mediatek MT8189, Qualcomm QCM2290,
QRB2210 and SM6115, SpacemiT K1, and TI TAS2568, TAS5802, TAS5806,
TAS5815, TAS5828 and TAS5830
- Usual HD-audio and USB-audio quirks and fixups
- Support for Onkyo SE-300PCIE, TASCAM IF-FW/DM MkII
Some gpiolib changes for shared GPIOs are included along with this PR
for covering ASoC drivers changes"
* tag 'sound-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (739 commits)
ALSA: hda/realtek: Add PCI SSIDs to HP ProBook quirks
ALSA: usb-audio: Simplify with usb_endpoint_max_periodic_payload()
ALSA: hda/realtek: fix mute/micmute LEDs don't work for more HP laptops
ALSA: rawmidi: Fix inconsistent indenting warning reported by smatch
ALSA: dice: fix buffer overflow in detect_stream_formats()
ASoC: codecs: Modify awinic amplifier dsp read and write functions
ASoC: SDCA: Fixup some more Kconfig issues
ASoC: cs35l56: Log a message if firmware is missing
ASoC: nau8325: Delete a stray tab
firmware: cs_dsp: Add test cases for client_ops == NULL
firmware: cs_dsp: Don't require client to provide a struct cs_dsp_client_ops
ASoC: fsl_micfil: Set channel range control
ASoC: fsl_micfil: Add default quality for different platforms
ASoC: intel: sof_sdw: Add codec_info for cs42l45
ASoC: sdw_utils: Add cs42l45 support functions
ASoC: intel: sof_sdw: Add ability to have auxiliary devices
ASoC: sdw_utils: Move codec_name to dai info
ASoC: sdw_utils: Add codec_conf for every DAI
ASoC: SDCA: Add terminal type into input/output widget name
ASoC: SDCA: Align mute controls to ALSA expectations
...
Linus Torvalds [Thu, 4 Dec 2025 16:53:30 +0000 (08:53 -0800)]
Merge tag 'drm-next-2025-12-03' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"There was a rather late merge of a new color pipeline feature, that
some userspace projects are blocked on, and has seen a lot of work in
amdgpu. This should have seen some time in -next. There is additional
support for this for Intel, that if it arrives in the next day or two
I'll pass it on in another pull request and you can decide if you want
to take it.
Highlights:
- Arm Ethos NPU accelerator driver
- new DRM color pipeline support
- amdgpu will now run discrete SI/CIK cards instead of radeon, which
enables vulkan support in userspace
- msm gets gen8 gpu support
- initial Xe3P support in xe
Full detail summary:
New driver:
- Arm Ethos-U65/U85 accel driver
Core:
- support the drm color pipeline in vkms/amdgfx
- add support for drm colorop pipeline
- add COLOR PIPELINE plane property
- add DRM_CLIENT_CAP_PLANE_COLOR_PIPELINE
- throttle dirty worker with vblank
- use drm_for_each_bridge_in_chain_scoped in drm's bridge code
- Ensure drm_client_modeset tests are enabled in UML
- add simulated vblank interrupt - use in drivers
- dumb buffer sizing helper
- move freeing of drm client memory to driver
- crtc sharpness strength property
- stop using system_wq in scheduler/drivers
- support emergency restore in drm-client
Rust:
- make slice::as_flattened usable on all supported rustc
- add FromBytes::from_bytes_prefix() method
- remove redundant device ptr from Rust GEM object
- Change how AlwaysRefCounted is implemented for GEM objects
gpuvm:
- Add deferred vm_bo cleanup to GPUVM (for rust)
atomic:
- cleanup and improve state handling interfaces
dp:
- add POST_LT_ADJ_REQ training sequence
- DPCD dSC quirk for synaptics panamera devices
- helpers to query branch DSC max throughput
ttm:
- Rename ttm_bo_put to ttm_bo_fini
- allow page protection flags on risc-v
- rework pipelined eviction fence handling
amdgpu:
- enable amdgpu by default for SI/CI dGPUs
- enable DC by default on SI
- refactor CIK/SI enablement
- add ABM KMS property
- Re-enable DM idle optimizations
- DC Analog encoders support
- Powerplay fixes for fiji/iceland
- Enable DC on bonaire by default
- HMM cleanup
- Add new RAS framework
- DML2.1 updates
- YCbCr420 fixes
- DC FP fixes
- DMUB fixes
- LTTPR fixes
- DTBCLK fixes
- DMU cursor offload handling
- Userq validation improvements
- Unify shutdown callback handling
- Suspend improvements
- Power limit code cleanup
- SR-IOV fixes
- AUX backlight fixes
- DCN 3.5 fixes
- HDMI compliance fixes
- DCN 4.0.1 cursor updates
- DCN interrupt fix
- DC KMS full update improvements
- Add additional HDCP traces
- DCN 3.2 fixes
- DP MST fixes
- Add support for new SR-IOV mailbox interface
- UQ reset support
- HDP flush rework
- VCE1 support
amdkfd:
- HMM cleanups
- Relax checks on save area overallocations
- Fix GPU mappings after prefetch
radeon:
- refactor CIK/SI enablement
xe:
- Initial Xe3P support
- panic support on VRAM for display
- fix stolen size check
- Loosen used tracking restriction
- New SR-IOV debugfs structure and debugfs updates
- Hide the GPU madvise flag behind a VM_BIND flag
- Always expose VRAM provisioning data on discrete GPUs
- Allow VRAM mappings for userptr when used with SVM
- Allow pinning of p2p dma-buf
- Use per-tile debugfs where appropriate
- Add documentation for Execution Queues
- PF improvements
- VF migration recovery redesign work
- User / Kernel VRAM partitioning
- Update Tile-based messages
- Allow configfs to disable specific GT types
- VF provisioning and migration improvements
- use SVM range helpers in PT layer
- Initial CRI support
- access VF registers using dedicated MMIO view
- limit number of jobs per exec queue
- add sriov_admin sysfs tree
- more crescent island specific support
- debugfs residency counter
- SRIOV migration work
- runtime registers for GFX 35
i915:
- add initial Xe3p_LPD display version 35 support
- Enable LNL+ content adaptive sharpness filter
- Use optimized VRR guardband
- Enable Xe3p LT PHY
- enable FBC support for Xe3p_LPD display
- add display 30.02 firmware support
- refactor SKL+ watermark latency setup
- refactor fbdev handling
- call i915/xe runtime PM via function pointers
- refactor i915/xe stolen memory/display interfaces
- use display version instead of gfx version in display code
- extend i915_display_info with Type-C port details
- lots of display cleanups/refactorings
- set O_LARGEFILE in __create_shmem
- skuip guc communication warning on reset
- fix time conversions
- defeature DRRS on LNL+
- refactor intel_frontbuffer split between i915/xe/display
- convert inteL_rom interfaces to struct drm_device
- unify display register polling interfaces
- aovid lock inversion when pinning to GGTT on CHV/BXT+VTD
bridge:
- improve ref counting
- ti-sn65dsi86 - add support for DP mode with HPD
- synopsis: support CEC, init timer with correct freq
- ASL CS5263 DP-to-HDMI bridge support
nova-core:
- introduce bitfield! macro
- introduce safe integer converters
- GSP inits to fully booted state on Ampere
- Use more future-proof register for GPU identification
nova-drm:
- select NOVA_CORE
- 64-bit only
nouveau:
- improve reclocking on tegra 186+
- add large page and compression support
msm:
- GPU:
- Gen8 support: A840 (Kaanapali) and X2-85 (Glymur)
- A612 support
- MDSS:
- Added support for Glymur and QCS8300 platforms
- DPU:
- Enabled Quad-Pipe support, unlocking higher resolutions support
- Added support for Glymur platform
- Documented DPU on QCS8300 platform as supported
- DisplayPort:
- Added support for Glymur platform
- Added support lame remapping inside DP block
- Documented DisplayPort controller on QCS8300 and SM6150/QCS615
as supported
tegra:
- NVJPG driver
panfrost:
- display JM contexts over debugfs
- export JM contexts to userspace
- improve error and job handling
panthor:
- support custom ASN_HASH for mt8196
- support mali-G1 GPU
- flush shmem write before mapping buffers uncached
- make timeout per-queue instead of per-job
mediatek:
- MT8195/88 HDMIv2/DDCv2 support
rockchip:
- dsi: add support for RK3368
amdxdna:
- enhance runtime PM
- last hardware error reading uapi
- support firmware debug output
- add resource and telemetry data uapi
- preemption support
imx:
- add driver for HDMI TX Parallel audio interface
ivpu:
- add support for user-managed preemption buffer
- add userptr support
- update JSM firware API to 3.33.0
- add better alloc/free warnings
- fix page fault in unbind all bos
- rework bind/unbind of imported buffers
- enable MCA ECC signalling
- split fw runtime and global memory buffers
- add fdinfo memory statistics
tidss:
- convert to drm logging
- logging cleanup
ast:
- refactor generation init paths
- add per chip generation detect_tx_chip
- set quirks for each chip model
atmel-hlcdc:
- set LCDC_ATTRE register in plane disable
- set correct values for plane scaler
solomon:
- use drm helper for get_modes and move_valid
sitronix:
- fix output position when clearing screens
qaic:
- support dma-buf exports
- support new firmware's READ_DATA implementation
- sahara AIC200 image table update
- add sysfs support
- add coredump support
- add uevents support
- PM support
sun4i:
- layer refactors to decouple plane from output
- improve DE33 support
vc4:
- switch to generic CEC helpers
komeda:
- use drm_ logging functions
vkms:
- configfs support for display configuration
* tag 'drm-next-2025-12-03' of https://gitlab.freedesktop.org/drm/kernel: (1869 commits)
Revert "drm/amd: Skip power ungate during suspend for VPE"
drm/amdgpu: use common defines for HUB faults
drm/amdgpu/gmc12: add amdgpu_vm_handle_fault() handling
drm/amdgpu/gmc11: add amdgpu_vm_handle_fault() handling
drm/amdgpu: use static ids for ACP platform devs
drm/amdgpu/sdma6: Update SDMA 6.0.3 FW version to include UMQ protected-fence fix
drm/amdgpu: Forward VMID reservation errors
drm/amdgpu/gmc8: Delegate VM faults to soft IRQ handler ring
drm/amdgpu/gmc7: Delegate VM faults to soft IRQ handler ring
drm/amdgpu/gmc6: Delegate VM faults to soft IRQ handler ring
drm/amdgpu/gmc6: Cache VM fault info
drm/amdgpu/gmc6: Don't print MC client as it's unknown
drm/amdgpu/cz_ih: Enable soft IRQ handler ring
drm/amdgpu/tonga_ih: Enable soft IRQ handler ring
drm/amdgpu/iceland_ih: Enable soft IRQ handler ring
drm/amdgpu/cik_ih: Enable soft IRQ handler ring
drm/amdgpu/si_ih: Enable soft IRQ handler ring
drm/amd/display: fix typo in display_mode_core_structs.h
drm/amd/display: fix Smart Power OLED not working after S4
drm/amd/display: Move RGB-type check for audio sync to DCE HW sequence
...
Linus Torvalds [Thu, 4 Dec 2025 04:45:43 +0000 (20:45 -0800)]
Merge tag 'ntfs3_for_6.19' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"New code:
- support timestamps prior to epoch
- do not overwrite uptodate pages
- disable readahead for compressed files
- setting of dummy blocksize to read boot_block when mounting
- the run_lock initialization when loading $Extend
- initialization of allocated memory before use
- support for the NTFS3_IOC_SHUTDOWN ioctl
- check for minimum alignment when performing direct I/O reads
- check for shutdown in fsync
Fixes:
- mount failure for sparse runs in run_unpack()
- use-after-free of sbi->options in cmp_fnames
- KMSAN uninit bug after failed mi_read in mi_format_new
- uninit error after buffer allocation by __getname()
- KMSAN uninit-value in ni_create_attr_list
- double free of sbi->options->nls and ownership of fc->fs_private
- incorrect vcn adjustments in attr_collapse_range()
- mode update when ACL can be reduced to mode
- memory leaks in add sub record
Changes:
- refactor code, updated terminology, spelling
- do not kmap pages in (de)compression code
- after ntfs_look_free_mft(), code that fails must put mft_inode
- default mount options for "acl" and "prealloc"
Replaced:
- use unsafe_memcpy() to avoid memcpy size warning
- ntfs_bio_pages with page cache for compressed files"
* tag 'ntfs3_for_6.19' of https://github.com/Paragon-Software-Group/linux-ntfs3: (26 commits)
fs/ntfs3: check for shutdown in fsync
fs/ntfs3: change the default mount options for "acl" and "prealloc"
fs/ntfs3: Prevent memory leaks in add sub record
fs/ntfs3: out1 also needs to put mi
fs/ntfs3: Fix spelling mistake "recommened" -> "recommended"
fs/ntfs3: update mode in xattr when ACL can be reduced to mode
fs/ntfs3: check minimum alignment for direct I/O
fs/ntfs3: implement NTFS3_IOC_SHUTDOWN ioctl
fs/ntfs3: correct attr_collapse_range when file is too fragmented
ntfs3: fix double free of sbi->options->nls and clarify ownership of fc->fs_private
fs/ntfs3: Initialize allocated memory before use
fs/ntfs3: remove ntfs_bio_pages and use page cache for compressed I/O
ntfs3: avoid memcpy size warning
fs/ntfs3: fix KMSAN uninit-value in ni_create_attr_list
ntfs3: init run lock for extend inode
ntfs: set dummy blocksize to read boot_block when mounting
fs/ntfs3: disable readahead for compressed files
ntfs3: Fix uninit buffer allocated by __getname()
ntfs3: fix uninit memory after failed mi_read in mi_format_new
ntfs3: fix use-after-free of sbi->options in cmp_fnames
...
Linus Torvalds [Thu, 4 Dec 2025 04:37:15 +0000 (20:37 -0800)]
Merge tag 'ext4_for_linus-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"New features and improvements for the ext4 file system:
- Optimize online defragmentation by using folios instead of
individual buffer heads
- Improve error codes stored in the superblock when the journal
aborts
- Minor cleanups and clarifications in ext4_map_blocks()
- Add documentation of the casefold and encrypt flags
- Add support for file systems with a blocksize greater than the
pagesize
- Improve performance by enabling the caching the fact that an inode
does not have a Posix ACL
Various Bug Fixes:
- Fix false positive complaints from smatch
- Fix error code which is returned by ext4fs_dirhash() when Siphash
is used without the encryption key
- Fix races when writing to inline data files which could trigger a
BUG
- Fix potential NULL dereference when there is an corrupt file system
with an extended attribute value stored in a inode
- Fix false positive lockdep report when syzbot uses ext4 and ocfs2
together
- Fix false positive reported by DEPT by adjusting lock annotation
- Avoid a potential BUG_ON in jbd2 when a file system is massively
corrupted
- Fix a WARN_ON when superblock is corrupted with a non-NULL
terminated mount options field
- Add check if the userspace passes in a non-NULL terminated mount
options field to EXT4_IOC_SET_TUNE_SB_PARAM
- Fix a potential journal checksum failure whena file system is
copied while it is mounted read-only
- Fix a potential potential orphan file tracking error which only
showed on 32-bit systems
- Fix assertion checks in mballoc (which have to be explicitly enbled
by manually enabling AGGRESSIVE_CHECKS and recompiling)
- Avoid complaining about overly large orphan files created by mke2fs
with with file systems with a 64k block size"
* tag 'ext4_for_linus-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (58 commits)
ext4: mark inodes without acls in __ext4_iget()
ext4: enable block size larger than page size
ext4: add checks for large folio incompatibilities when BS > PS
ext4: support verifying data from large folios with fs-verity
ext4: make data=journal support large block size
ext4: support large block size in __ext4_block_zero_page_range()
ext4: support large block size in mpage_prepare_extent_to_map()
ext4: support large block size in mpage_map_and_submit_buffers()
ext4: support large block size in ext4_block_write_begin()
ext4: support large block size in ext4_mpage_readpages()
ext4: rename 'page' references to 'folio' in multi-block allocator
ext4: prepare buddy cache inode for BS > PS with large folios
ext4: support large block size in ext4_mb_init_cache()
ext4: support large block size in ext4_mb_get_buddy_page_lock()
ext4: support large block size in ext4_mb_load_buddy_gfp()
ext4: add EXT4_LBLK_TO_PG and EXT4_PG_TO_LBLK for block/page conversion
ext4: add EXT4_LBLK_TO_B macro for logical block to bytes conversion
ext4: support large block size in ext4_readdir()
ext4: support large block size in ext4_calculate_overhead()
ext4: introduce s_min_folio_order for future BS > PS support
...
Linus Torvalds [Thu, 4 Dec 2025 04:28:50 +0000 (20:28 -0800)]
Merge tag 'gfs2-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 updates from Andreas Gruenbacher:
- Major withdraw / error handling overhaul based on dlm's new
DLM_RELEASE_RECOVER feature: this allows gfs to treat withdraws like
node failures. Make withdraws asynchronous
- Fix a bug in commit e4a8b5481c59a that caused 'df' to remain out of
sync. ('df' is still allowed to go slightly out of sync for short
periods of time)
- Prevent recusive memory reclaim in gfs2_unstuff_dinode()
- Clean up SDF_JOURNAL_LIVE flag handling
- Fix remote evict for read-only filesystems
- Fix a misuse of bio_chain()
- Various other minor cleanups
* tag 'gfs2-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: (35 commits)
gfs2: Fix use of bio_chain
gfs2: Clean up SDF_JOURNAL_LIVE flag handling
gfs2: No longer thaw filesystems during a withdraw
gfs2: Withdraw immediately in gfs2_trans_add_meta
gfs2: New gfs2_withdraw_helper
gfs2: Clean up properly during a withdraw
gfs2: Rename gfs2_{gl_dq_holders => withdraw_glocks}
Revert "gfs2: fix infinite loop when checking ail item count before go_inval"
Revert "gfs2: Allow some glocks to be used during withdraw"
Revert "gfs2: Check for log write errors before telling dlm to unlock"
Revert "gfs2: fix a deadlock on withdraw-during-mount"
Revert "gfs2: Force withdraw to replay journals and wait for it to finish" (6/6)
Revert "gfs2: Force withdraw to replay journals and wait for it to finish" (5/6)
Revert "gfs2: Force withdraw to replay journals and wait for it to finish" (4/6)
Revert "gfs2: Force withdraw to replay journals and wait for it to finish" (3/6)
Revert "gfs2: Force withdraw to replay journals and wait for it to finish" (2/6)
Revert "gfs2: Force withdraw to replay journals and wait for it to finish" (1/6)
Revert "gfs2: don't stop reads while withdraw in progress"
gfs2: Rename LM_FLAG_{NOEXP -> RECOVER}
gfs2: Kill gfs2_io_error_bh_wd
...
Linus Torvalds [Thu, 4 Dec 2025 04:23:41 +0000 (20:23 -0800)]
Merge tag 'v6.19-rc-smb-fixes' of git://git.samba.org/ksmbd
Pull smb client and server updates from Steve French:
- server fixes:
- IPC use after free locking fix
- fix locking bug in delete paths
- fix use after free in disconnect
- fix underflow in locking check
- error mapping improvement
- socket listening improvement
- return code mapping fixes
- crypto improvements (use default libraries)
- cleanup patches:
- netfs
- client checkpatch cleanup
- server cleanup
- move server/client duplicate code to common code
- fix some defines to better match protocol specification
- smbdirect (RDMA) fixes
- client debugging improvements for leases
* tag 'v6.19-rc-smb-fixes' of git://git.samba.org/ksmbd: (44 commits)
cifs: Use netfs_alloc/free_folioq_buffer()
smb: client: show smb lease key in open_dirs output
smb: client: show smb lease key in open_files output
ksmbd: ipc: fix use-after-free in ipc_msg_send_request
smb: client: relax WARN_ON_ONCE(SMBDIRECT_SOCKET_*) checks in recv_done() and smbd_conn_upcall()
smb: server: relax WARN_ON_ONCE(SMBDIRECT_SOCKET_*) checks in recv_done() and smb_direct_cm_handler()
smb: smbdirect: introduce SMBDIRECT_CHECK_STATUS_{WARN,DISCONNECT}()
smb: smbdirect: introduce SMBDIRECT_DEBUG_ERR_PTR() helper
ksmbd: vfs: fix race on m_flags in vfs_cache
ksmbd: Replace strcpy + strcat to improve convert_to_nt_pathname
smb: move FILE_SYSTEM_ATTRIBUTE_INFO to common/fscc.h
ksmbd: implement error handling for STATUS_INFO_LENGTH_MISMATCH in smb server
ksmbd: fix use-after-free in ksmbd_tree_connect_put under concurrency
ksmbd: server: avoid busy polling in accept loop
smb: move create_durable_reconn to common/smb2pdu.h
smb: fix some warnings reported by scripts/checkpatch.pl
smb: do some cleanups
smb: move FILE_SYSTEM_SIZE_INFO to common/fscc.h
smb: move some duplicate struct definitions to common/fscc.h
smb: move list of FileSystemAttributes to common/fscc.h
...
Linus Torvalds [Thu, 4 Dec 2025 04:19:38 +0000 (20:19 -0800)]
Merge tag 'xfs-merge-6.19' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs updates from Carlos Maiolino:
"There are no major changes in xfs. This contains mostly some code
cleanups, a few bug fixes and documentation update. Highlights are:
- Quota locking cleanup
- Getting rid of old xlog_in_core_2_t type"
* tag 'xfs-merge-6.19' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (33 commits)
docs: remove obsolete links in the xfs online repair documentation
xfs: move some code out of xfs_iget_recycle
xfs: use zi more in xfs_zone_gc_mount
xfs: remove the unused bv field in struct xfs_gc_bio
xfs: remove xarray mark for reclaimable zones
xfs: remove the xlog_in_core_t typedef
xfs: remove l_iclog_heads
xfs: remove the xlog_rec_header_t typedef
xfs: remove xlog_in_core_2_t
xfs: remove a very outdated comment from xlog_alloc_log
xfs: cleanup xlog_alloc_log a bit
xfs: don't use xlog_in_core_2_t in struct xlog_in_core
xfs: add a on-disk log header cycle array accessor
xfs: add a XLOG_CYCLE_DATA_SIZE constant
xfs: reduce ilock roundtrips in xfs_qm_vop_dqalloc
xfs: move xfs_dquot_tree calls into xfs_qm_dqget_cache_{lookup,insert}
xfs: move quota locking into xrep_quota_item
xfs: move quota locking into xqcheck_commit_dquot
xfs: move q_qlock locking into xqcheck_compare_dquot
xfs: move q_qlock locking into xchk_quota_item
...
Linus Torvalds [Thu, 4 Dec 2025 04:14:44 +0000 (20:14 -0800)]
Merge tag 'erofs-for-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs updates from Gao Xiang:
- Fix a WARNING caused by a recent FSDAX misdetection regression
- Fix the filesystem stacking limit for file-backed mounts
- Print more informative diagnostics on decompression errors
- Switch the on-disk definition `erofs_fs.h` to the MIT license
- Minor cleanups
* tag 'erofs-for-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: switch on-disk header `erofs_fs.h` to MIT license
erofs: get rid of raw bi_end_io() usage
erofs: enable error reporting for z_erofs_fixup_insize()
erofs: enable error reporting for z_erofs_stream_switch_bufs()
erofs: improve Zstd, LZMA and DEFLATE error strings
erofs: improve decompression error reporting
erofs: tidy up z_erofs_lz4_handle_overlap()
erofs: limit the level of fs stacking for file-backed mounts
erofs: correct FSDAX detection
Linus Torvalds [Thu, 4 Dec 2025 04:08:32 +0000 (20:08 -0800)]
Merge tag 'hfs-v6.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/vdubeyko/hfs
Pull hfs/hfsplus updates from Viacheslav Dubeyko:
"Several fixes for syzbot reported issues, HFS/HFS+ fixes of xfstests
failures, Kunit-based unit-tests introduction, and code cleanup:
- Dan Carpenter fixed a potential use-after-free issue in
hfs_correct_next_unused_CNID() method. Tetsuo Handa has made nice
fix of syzbot reported issue related to incorrect inode->i_mode
management if volume has been corrupted somehow. Yang Chenzhi has
made really good fix of potential race condition in
__hfs_bnode_create() method for HFS+ file system.
- Several fixes to xfstests failures. Particularly, generic/070,
generic/073, and generic/101 test-cases finish successfully for the
case of HFS+ file system right now.
- HFS and HFS+ drivers share multiple structures of on-disk layout
declarations. Some structures are used without any change. However,
we had two independent declarations of the same structures in HFS
and HFS+ drivers.
The on-disk layout declarations have been moved into
include/linux/hfs_common.h with the goal to exclude the
declarations duplication and to keep the HFS/HFS+ on-disk layout
declarations in one place.
Also, this patch prepares the basis for creating a hfslib that can
aggregate common functionality without necessity to duplicate the
same code in HFS and HFS+ drivers.
- HFS/HFS+ really need unit-tests because of multiple xfstests
failures. The first two patches introduce Kunit-based unit-tests
for the case string operations in HFS/HFS+ file system drivers"
* tag 'hfs-v6.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/vdubeyko/hfs:
hfs/hfsplus: move on-disk layout declarations into hfs_common.h
hfsplus: fix volume corruption issue for generic/101
hfsplus: introduce KUnit tests for HFS+ string operations
hfs: introduce KUnit tests for HFS string operations
hfsplus: fix volume corruption issue for generic/073
hfsplus: Verify inode mode when loading from disk
hfsplus: fix volume corruption issue for generic/070
hfs/hfsplus: prevent getting negative values of offset/length
hfsplus: fix missing hfs_bnode_get() in __hfs_bnode_create
hfs: fix potential use after free in hfs_correct_next_unused_CNID()
Linus Torvalds [Thu, 4 Dec 2025 04:03:46 +0000 (20:03 -0800)]
Merge tag 'for-6.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"Features:
- shutdown ioctl support (needs CONFIG_BTRFS_EXPERIMENTAL for now):
- set filesystem state as being shut down (also named going down
in other filesystems), where all active operations return EIO
and this cannot be changed until unmount
- pending operations are attempted to be finished but error
messages may still show up depending on where exactly the
shutdown happened
- scrub (and device replace) vs suspend/hibernate:
- a running scrub will prevent suspend, which can be annoying as
suspend is an immediate request and scrub is not critical
- filesystem freezing before suspend was not sufficient as the
problem was in process freezing
- behaviour change: on suspend scrub and device replace are
cancelled, where scrub can record the last state and continue
from there; the device replace has to be restarted from the
beginning
- zone stats exported in sysfs, from the perspective of the
filesystem this includes active, reclaimable, relocation etc zones
Performance:
- improvements when processing space reservation tickets by
optimizing locking and shrinking critical sections, cumulative
improvements in lockstat numbers show +15%
Notable fixes:
- use vmalloc fallback when allocating bios as high order allocations
can happen with wide checksums (like sha256)
- scrub will always track the last position of progress so it's not
starting from zero after an error
Core:
- under experimental config, checksum calculations are offloaded to
process context, simplifies locking and allows to remove
compression write worker kthread(s):
- speed improvement in direct IO throughput with buffered IO
fallback is +15% when not offloaded but this is more related to
internal crypto subsystem improvements
- this will be probably default in the future removing the sysfs
tunable
- (experimental) block size > page size updates:
- support more operations when not using large folios (encoded
read/write and send)
- raid56
- more preparations for fscrypt support
Other:
- more conversions to auto-cleaned variables
- parameter cleanups and removals
- extended warning fixes
- improved printing of structured values like keys
- lots of other cleanups and refactoring"
* tag 'for-6.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (147 commits)
btrfs: remove unnecessary inode key in btrfs_log_all_parents()
btrfs: remove redundant zero/NULL initializations in btrfs_alloc_root()
btrfs: remaining BTRFS_PATH_AUTO_FREE conversions
btrfs: send: do not allocate memory for xattr data when checking it exists
btrfs: send: add unlikely to all unexpected overflow checks
btrfs: reduce arguments to btrfs_del_inode_ref_in_log()
btrfs: remove root argument from btrfs_del_dir_entries_in_log()
btrfs: use test_and_set_bit() in btrfs_delayed_delete_inode_ref()
btrfs: don't search back for dir inode item in INO_LOOKUP_USER
btrfs: don't rewrite ret from inode_permission
btrfs: add orig_logical to btrfs_bio for encryption
btrfs: disable verity on encrypted inodes
btrfs: disable various operations on encrypted inodes
btrfs: remove redundant level reset in btrfs_del_items()
btrfs: simplify leaf traversal after path release in btrfs_next_old_leaf()
btrfs: optimize balance_level() path reference handling
btrfs: factor out root promotion logic into promote_child_to_root()
btrfs: raid56: remove the "_step" infix
btrfs: raid56: enable bs > ps support
btrfs: raid56: prepare finish_parity_scrub() to support bs > ps cases
...
Linus Torvalds [Thu, 4 Dec 2025 03:26:18 +0000 (19:26 -0800)]
Merge tag 'for-6.19/block-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block updates from Jens Axboe:
- Fix head insertion for mq-deadline, a regression from when priority
support was added
- Series simplifying and improving the ublk user copy code
- Various ublk related cleanups
- Fixup REQ_NOWAIT handling in loop/zloop, clearing NOWAIT when the
request is punted to a thread for handling
- Merge and then later revert loop dio nowait support, as it ended up
causing excessive stack usage for when the inline issue code needs to
dip back into the full file system code
- Improve auto integrity code, making it less deadlock prone
- Speedup polled IO handling, but manually managing the hctx lookups
- Fixes for blk-throttle for SSD devices
- Small series with fixes for the S390 dasd driver
- Add support for caching zones, avoiding unnecessary report zone
queries
- MD pull requests via Yu:
- fix null-ptr-dereference regression for dm-raid0
- fix IO hang for raid5 when array is broken with IO inflight
- remove legacy 1s delay to speed up system shutdown
- change maintainer's email address
- data can be lost if array is created with different lbs devices,
fix this problem and record lbs of the array in metadata
- fix rcu protection for md_thread
- fix mddev kobject lifetime regression
- enable atomic writes for md-linear
- some cleanups
- bcache updates via Coly
- remove useless discard and cache device code
- improve usage of per-cpu workqueues
- Reorganize the IO scheduler switching code, fixing some lockdep
reports as well
- Improve the block layer P2P DMA support
- Add support to the block tracing code for zoned devices
- Segment calculation improves, and memory alignment flexibility
improvements
- Set of prep and cleanups patches for ublk batching support. The
actual batching hasn't been added yet, but helps shrink down the
workload of getting that patchset ready for 6.20
- Fix for how the ps3 block driver handles segments offsets
- Improve how block plugging handles batch tag allocations
- nbd fixes for use-after-free of the configuration on device clear/put
- Set of improvements and fixes for zloop
- Add Damien as maintainer of the block zoned device code handling
- Various other fixes and cleanups
* tag 'for-6.19/block-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (162 commits)
block/rnbd: correct all kernel-doc complaints
blk-mq: use queue_hctx in blk_mq_map_queue_type
md: remove legacy 1s delay in md_notify_reboot
md/raid5: fix IO hang when array is broken with IO inflight
md: warn about updating super block failure
md/raid0: fix NULL pointer dereference in create_strip_zones() for dm-raid
sbitmap: fix all kernel-doc warnings
ublk: add helper of __ublk_fetch()
ublk: pass const pointer to ublk_queue_is_zoned()
ublk: refactor auto buffer register in ublk_dispatch_req()
ublk: add `union ublk_io_buf` with improved naming
ublk: add parameter `struct io_uring_cmd *` to ublk_prep_auto_buf_reg()
kfifo: add kfifo_alloc_node() helper for NUMA awareness
blk-mq: fix potential uaf for 'queue_hw_ctx'
blk-mq: use array manage hctx map instead of xarray
ublk: prevent invalid access with DEBUG
s390/dasd: Use scnprintf() instead of sprintf()
s390/dasd: Move device name formatting into separate function
s390/dasd: Remove unnecessary debugfs_create() return checks
s390/dasd: Fix gendisk parent after copy pair swap
...
Linus Torvalds [Thu, 4 Dec 2025 02:58:57 +0000 (18:58 -0800)]
Merge tag 'for-6.19/io_uring-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull io_uring updates from Jens Axboe:
- Unify how task_work cancelations are detected, placing it in the
task_work running state rather than needing to check the task state
- Series cleaning up and moving the cancelation code to where it
belongs, in cancel.c
- Cleanup of waitid and futex argument handling
- Add support for mixed sized SQEs. 6.18 added support for mixed sized
CQEs, improving flexibility and efficiency of workloads that need big
CQEs. This adds similar support for SQEs, where the occasional need
for a 128b SQE doesn't necessitate having all SQEs be 128b in size
- Introduce zcrx and SQ/CQ layout queries. The former returns what zcrx
features are available. And both return the ring size information to
help with allocation size calculation for user provided rings like
IORING_SETUP_NO_MMAP and IORING_MEM_REGION_TYPE_USER
- Zcrx updates for 6.19. It includes a bunch of small patches,
IORING_REGISTER_ZCRX_CTRL and RQ flushing and David's work on sharing
zcrx b/w multiple io_uring instances
- Series cleaning up ring initializations, notable deduplicating ring
size and offset calculations. It also moves most of the checking
before doing any allocations, making the code simpler
- Add support for getsockname and getpeername, which is mostly a
trivial hookup after a bit of refactoring on the networking side
- Various fixes and cleanups
* tag 'for-6.19/io_uring-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (68 commits)
io_uring: Introduce getsockname io_uring cmd
socket: Split out a getsockname helper for io_uring
socket: Unify getsockname and getpeername implementation
io_uring/query: drop unused io_handle_query_entry() ctx arg
io_uring/kbuf: remove obsolete buf_nr_pages and update comments
io_uring/register: use correct location for io_rings_layout
io_uring/zcrx: share an ifq between rings
io_uring/zcrx: add io_fill_zcrx_offsets()
io_uring/zcrx: export zcrx via a file
io_uring/zcrx: move io_zcrx_scrub() and dependencies up
io_uring/zcrx: count zcrx users
io_uring/zcrx: add sync refill queue flushing
io_uring/zcrx: introduce IORING_REGISTER_ZCRX_CTRL
io_uring/zcrx: elide passing msg flags
io_uring/zcrx: use folio_nr_pages() instead of shift operation
io_uring/zcrx: convert to use netmem_desc
io_uring/query: introduce rings info query
io_uring/query: introduce zcrx query
io_uring: move cq/sq user offset init around
io_uring: pre-calculate scq layout
...
Linus Torvalds [Thu, 4 Dec 2025 01:24:33 +0000 (17:24 -0800)]
Merge tag 'net-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Replace busylock at the Tx queuing layer with a lockless list.
Resulting in a 300% (4x) improvement on heavy TX workloads, sending
twice the number of packets per second, for half the cpu cycles.
- Allow constantly busy flows to migrate to a more suitable CPU/NIC
queue.
Normally we perform queue re-selection when flow comes out of idle,
but under extreme circumstances the flows may be constantly busy.
Add sysctl to allow periodic rehashing even if it'd risk packet
reordering.
- Optimize the NAPI skb cache, make it larger, use it in more paths.
- Attempt returning Tx skbs to the originating CPU (like we already
did for Rx skbs).
- Various data structure layout and prefetch optimizations from Eric.
- Remove ktime_get() from the recvmsg() fast path, ktime_get() is
sadly quite expensive on recent AMD machines.
- Extend threaded NAPI polling to allow the kthread busy poll for
packets.
- Make MPTCP use Rx backlog processing. This lowers the lock
pressure, improving the Rx performance.
- Support memcg accounting of MPTCP socket memory.
- Allow admin to opt sockets out of global protocol memory accounting
(using a sysctl or BPF-based policy). The global limits are a poor
fit for modern container workloads, where limits are imposed using
cgroups.
- Improve heuristics for when to kick off AF_UNIX garbage collection.
- Allow users to control TCP SACK compression, and default to 33% of
RTT.
- Add tcp_rcvbuf_low_rtt sysctl to let datacenter users avoid
unnecessarily aggressive rcvbuf growth and overshot when the
connection RTT is low.
- Preserve skb metadata space across skb_push / skb_pull operations.
- Support for IPIP encapsulation in the nftables flowtable offload.
- Support appending IP interface information to ICMP messages (RFC
5837).
- Support setting max record size in TLS (RFC 8449).
- Remove taking rtnl_lock from RTM_GETNEIGHTBL and RTM_SETNEIGHTBL.
- Use a dedicated lock (and RCU) in MPLS, instead of rtnl_lock.
- Let users configure the number of write buffers in SMC.
- Add new struct sockaddr_unsized for sockaddr of unknown length,
from Kees.
- Some conversions away from the crypto_ahash API, from Eric Biggers.
- Some preparations for slimming down struct page.
- YAML Netlink protocol spec for WireGuard.
- Add a tool on top of YAML Netlink specs/lib for reporting commonly
computed derived statistics and summarized system state.
Driver API:
- Add CAN XL support to the CAN Netlink interface.
- Add uAPI for reporting PHY Mean Square Error (MSE) diagnostics, as
defined by the OPEN Alliance's "Advanced diagnostic features for
100BASE-T1 automotive Ethernet PHYs" specification.
- Add DPLL phase-adjust-gran pin attribute (and implement it in
zl3073x).
- Refactor xfrm_input lock to reduce contention when NIC offloads
IPsec and performs RSS.
- Add info to devlink params whether the current setting is the
default or a user override. Allow resetting back to default.
- Add standard device stats for PSP crypto offload.
- Leverage DSA frame broadcast to implement simple HSR frame
duplication for a lot of switches without dedicated HSR offload.
- Convert drivers to support dedicated ops for timestamping control,
and away from the direct IOCTL handling. While at it support GET
operations for PHY timestamping.
- Add (and convert most drivers to) a dedicated ethtool callback for
reading the Rx ring count.
- Significant refactoring efforts in the STMMAC driver, which
supports Synopsys turn-key MAC IP integrated into a ton of SoCs.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support PPS in/out on all pins
- Intel (100G, ice, idpf):
- ice: implement standard ethtool and timestamping stats
- i40e: support setting the max number of MAC addresses per VF
- iavf: support RSS of GTP tunnels for 5G and LTE deployments
- nVidia/Mellanox (mlx5):
- reduce downtime on interface reconfiguration
- disable being an XDP redirect target by default (same as
other drivers) to avoid wasting resources if feature is
unused
- Meta (fbnic):
- add support for Linux-managed PCS on 25G, 50G, and 100G links
- Wangxun:
- support Rx descriptor merge, and Tx head writeback
- support Rx coalescing offload
- support 25G SPF and 40G QSFP modules
- Ethernet virtual:
- Google (gve):
- allow ethtool to configure rx_buf_len
- implement XDP HW RX Timestamping support for DQ descriptor
format
- Microsoft vNIC (mana):
- support HW link state events
- handle hardware recovery events when probing the device
- Ethernet NICs consumer, and embedded:
- usbnet: add support for Byte Queue Limits (BQL)
- AMD (amd-xgbe):
- add device selftests
- NXP (enetc):
- add i.MX94 support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- bcmasp: add support for PHY-based Wake-on-LAN
- Broadcom switches (b53):
- support port isolation
- support BCM5389/97/98 and BCM63XX ARL formats
- Lantiq/MaxLinear switches:
- support bridge FDB entries on the CPU port
- use regmap for register access
- allow user to enable/disable learning
- support Energy Efficient Ethernet
- support configuring RMII clock delays
- add tagging driver for MaxLinear GSW1xx switches
- Synopsys (stmmac):
- support using the HW clock in free running mode
- add Eswin EIC7700 support
- add Rockchip RK3506 support
- add Altera Agilex5 support
- Cadence (macb):
- cleanup and consolidate descriptor and DMA address handling
- add EyeQ5 support
- TI:
- icssg-prueth: support AF_XDP
- Airoha access points:
- add missing Ethernet stats and link state callback
- add AN7583 support
- support out-of-order Tx completion processing
- Power over Ethernet:
- pd692x0: preserve PSE configuration across reboots
- add support for TPS23881B devices
- Ethernet PHYs:
- Open Alliance OATC14 10BASE-T1S PHY cable diagnostic support
- Support 50G SerDes and 100G interfaces in Linux-managed PHYs
- micrel:
- support for non PTP SKUs of lan8814
- enable in-band auto-negotiation on lan8814
- realtek:
- cable testing support on RTL8224
- interrupt support on RTL8221B
- motorcomm: support for PHY LEDs on YT853
- microchip: support for LAN867X Rev.D0 PHYs w/ SQI and cable diag
- mscc: support for PHY LED control
- CAN drivers:
- m_can: add support for optional reset and system wake up
- remove can_change_mtu() obsoleted by core handling
- mcp251xfd: support GPIO controller functionality
- Bluetooth:
- add initial support for PASTa
- WiFi:
- split ieee80211.h file, it's way too big
- improvements in VHT radiotap reporting, S1G, Channel Switch
Announcement handling, rate tracking in mesh networks
- improve multi-radio monitor mode support, and add a cfg80211
debugfs interface for it
- HT action frame handling on 6 GHz
- initial chanctx work towards NAN
- MU-MIMO sniffer improvements
- WiFi drivers:
- RealTek (rtw89):
- support USB devices RTL8852AU and RTL8852CU
- initial work for RTL8922DE
- improved injection support
- Intel:
- iwlwifi: new sniffer API support
- MediaTek (mt76):
- WED support for >32-bit DMA
- airoha NPU support
- regdomain improvements
- continued WiFi7/MLO work
- Qualcomm/Atheros:
- ath10k: factory test support
- ath11k: TX power insertion support
- ath12k: BSS color change support
- ath12k: statistics improvements
- brcmfmac: Acer A1 840 tablet quirk
- rtl8xxxu: 40 MHz connection fixes/support"
* tag 'net-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1381 commits)
net: page_pool: sanitise allocation order
net: page pool: xa init with destroy on pp init
net/mlx5e: Support XDP target xmit with dummy program
net/mlx5e: Update XDP features in switch channels
selftests/tc-testing: Test CAKE scheduler when enqueue drops packets
net/sched: sch_cake: Fix incorrect qlen reduction in cake_drop
wireguard: netlink: generate netlink code
wireguard: uapi: generate header with ynl-gen
wireguard: uapi: move flag enums
wireguard: uapi: move enum wg_cmd
wireguard: netlink: add YNL specification
selftests: drv-net: Fix tolerance calculation in devlink_rate_tc_bw.py
selftests: drv-net: Fix and clarify TC bandwidth split in devlink_rate_tc_bw.py
selftests: drv-net: Set shell=True for sysfs writes in devlink_rate_tc_bw.py
selftests: drv-net: Use Iperf3Runner in devlink_rate_tc_bw.py
selftests: drv-net: introduce Iperf3Runner for measurement use cases
selftests: drv-net: Add devlink_rate_tc_bw.py to TEST_PROGS
net: ps3_gelic_net: Use napi_alloc_skb() and napi_gro_receive()
Documentation: net: dsa: mention simple HSR offload helpers
Documentation: net: dsa: mention availability of RedBox
...
Linus Torvalds [Thu, 4 Dec 2025 00:54:54 +0000 (16:54 -0800)]
Merge tag 'bpf-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf updates from Alexei Starovoitov:
- Convert selftests/bpf/test_tc_edt and test_tc_tunnel from .sh to
test_progs runner (Alexis Lothoré)
- Convert selftests/bpf/test_xsk to test_progs runner (Bastien
Curutchet)
- Replace bpf memory allocator with kmalloc_nolock() in
bpf_local_storage (Amery Hung), and in bpf streams and range tree
(Puranjay Mohan)
- Introduce support for indirect jumps in BPF verifier and x86 JIT
(Anton Protopopov) and arm64 JIT (Puranjay Mohan)
- Remove runqslower bpf tool (Hoyeon Lee)
- Fix corner cases in the verifier to close several syzbot reports
(Eduard Zingerman, KaFai Wan)
- Several improvements in deadlock detection in rqspinlock (Kumar
Kartikeya Dwivedi)
- Implement "jmp" mode for BPF trampoline and corresponding
DYNAMIC_FTRACE_WITH_JMP. It improves "fexit" program type performance
from 80 M/s to 136 M/s. With Steven's Ack. (Menglong Dong)
- Add ability to test non-linear skbs in BPF_PROG_TEST_RUN (Paul
Chaignon)
- Do not let BPF_PROG_TEST_RUN emit invalid GSO types to stack (Daniel
Borkmann)
- Generalize buildid reader into bpf_dynptr (Mykyta Yatsenko)
- Optimize bpf_map_update_elem() for map-in-map types (Ritesh
Oedayrajsingh Varma)
- Introduce overwrite mode for BPF ring buffer (Xu Kuohai)
* tag 'bpf-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (169 commits)
bpf: optimize bpf_map_update_elem() for map-in-map types
bpf: make kprobe_multi_link_prog_run always_inline
selftests/bpf: do not hardcode target rate in test_tc_edt BPF program
selftests/bpf: remove test_tc_edt.sh
selftests/bpf: integrate test_tc_edt into test_progs
selftests/bpf: rename test_tc_edt.bpf.c section to expose program type
selftests/bpf: Add success stats to rqspinlock stress test
rqspinlock: Precede non-head waiter queueing with AA check
rqspinlock: Disable spinning for trylock fallback
rqspinlock: Use trylock fallback when per-CPU rqnode is busy
rqspinlock: Perform AA checks immediately
rqspinlock: Enclose lock/unlock within lock entry acquisitions
bpf: Remove runqslower tool
selftests/bpf: Remove usage of lsm/file_alloc_security in selftest
bpf: Disable file_alloc_security hook
bpf: check for insn arrays in check_ptr_alignment
bpf: force BPF_F_RDONLY_PROG on insn array creation
bpf: Fix exclusive map memory leak
selftests/bpf: Make CS length configurable for rqspinlock stress test
selftests/bpf: Add lock wait time stats to rqspinlock stress test
...
Linus Torvalds [Wed, 3 Dec 2025 23:50:11 +0000 (15:50 -0800)]
Merge tag 'linux_kselftest-kunit-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit updates from Shuah Khan:
- Make filter parameters configurable via Kconfig
- Add description of kunit.enable parameter to documentation
* tag 'linux_kselftest-kunit-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: Make filter parameters configurable via Kconfig
Documentation: kunit: add description of kunit.enable parameter
Linus Torvalds [Wed, 3 Dec 2025 23:08:18 +0000 (15:08 -0800)]
Merge tag 'linux_kselftest-next-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
- Add basic test for trace_marker_raw file to tracing selftest
- Fix invalid array access in printf dma_map_benchmark selftest
- Add tprobe enable/disable testcase to tracing selftest
- Update fprobe selftest for ftrace based fprobe
* tag 'linux_kselftest-next-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: tracing: Update fprobe selftest for ftrace based fprobe
selftests: tracing: Add tprobe enable/disable testcase
selftests/run_kselftest.sh: exit with error if tests fail
selftests/dma: fix invalid array access in printf
selftests/tracing: Add basic test for trace_marker_raw file
Linus Torvalds [Wed, 3 Dec 2025 22:42:21 +0000 (14:42 -0800)]
Merge tag 'kbuild-6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild updates from Nicolas Schier:
- Enable -fms-extensions, allowing anonymous use of tagged struct or
union in struct/union (tag kbuild-ms-extensions-6.19). An exemplary
conversion patch is added here, too (btrfs).
[ Editor's note: the core of this actually came in early through a
shared branch and a few other trees - Linus ]
- Introduce architecture-specific CC_CAN_LINK and flags for userprogs
- Add new packaging target 'modules-cpio-pkg' for building a initramfs
cpio w/ kmods
- Handle included .c files in gen_compile_commands
- Minor kbuild changes:
- Use objtree for module signing key path, fixing oot kmod signing
- Improve documentation of KBUILD_BUILD_TIMESTAMP
- Reuse KBUILD_USERCFLAGS for UAPI, instead of defining twice
- Rename scripts/Makefile.extrawarn to Makefile.warn
- Drop obsolete types.h check from headers_check.pl
- Remove outdated config leak ignore entries
* tag 'kbuild-6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: add target to build a cpio containing modules
initramfs: add gen_init_cpio to hostprogs unconditionally
kbuild: allow architectures to override CC_CAN_LINK
init: deduplicate cc-can-link.sh invocations
kbuild: don't enable CC_CAN_LINK if the dummy program generates warnings
scripts: headers_install.sh: Remove two outdated config leak ignore entries
scripts/clang-tools: Handle included .c files in gen_compile_commands
kbuild: uapi: Drop types.h check from headers_check.pl
kbuild: Rename Makefile.extrawarn to Makefile.warn
MAINTAINERS, .mailmap: Update mail address for Nicolas Schier
kbuild: uapi: reuse KBUILD_USERCFLAGS
kbuild: doc: improve KBUILD_BUILD_TIMESTAMP documentation
kbuild: Use objtree for module signing key path
btrfs: send: make use of -fms-extensions for defining struct fs_path
Linus Torvalds [Wed, 3 Dec 2025 22:16:49 +0000 (14:16 -0800)]
Merge tag 'rust-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull Rust updates from Miguel Ojeda:
"Toolchain and infrastructure:
- Add support for 'syn'.
Syn is a parsing library for parsing a stream of Rust tokens into a
syntax tree of Rust source code.
Currently this library is geared toward use in Rust procedural
macros, but contains some APIs that may be useful more generally.
'syn' allows us to greatly simplify writing complex macros such as
'pin-init' (Benno has already prepared the 'syn'-based version). We
will use it in the 'macros' crate too.
'syn' is the most downloaded Rust crate (according to crates.io),
and it is also used by the Rust compiler itself. While the amount
of code is substantial, there should not be many updates needed for
these crates, and even if there are, they should not be too big,
e.g. +7k -3k lines across the 3 crates in the last year.
'syn' requires two smaller dependencies: 'quote' and 'proc-macro2'.
I only modified their code to remove a third dependency
('unicode-ident') and to add the SPDX identifiers. The code can be
easily verified to exactly match upstream with the provided
scripts.
They are all licensed under "Apache-2.0 OR MIT", like the other
vendored 'alloc' crate we had for a while.
Please see the merge commit with the cover letter for more context.
- Allow 'unreachable_pub' and 'clippy::disallowed_names' for
doctests.
Examples (i.e. doctests) may want to do things like show public
items and use names such as 'foo'.
Nevertheless, we still try to keep examples as close to real code
as possible (this is part of why running Clippy on doctests is
important for us, e.g. for safety comments, which userspace Rust
does not support yet but we are stricter).
'kernel' crate:
- Replace our custom 'CStr' type with 'core::ffi::CStr'.
Using the standard library type reduces our custom code footprint,
and we retain needed custom functionality through an extension
trait and a new 'fmt!' macro which replaces the previous 'core'
import.
This started in 6.17 and continued in 6.18, and we finally land the
replacement now. This required quite some stamina from Tamir, who
split the changes in steps to prepare for the flag day change here.
- Replace 'kernel::c_str!' with C string literals.
C string literals were added in Rust 1.77, which produce '&CStr's
(the 'core' one), so now we can write:
c"hi"
instead of:
c_str!("hi")
- Add 'num' module for numerical features.
It includes the 'Integer' trait, implemented for all primitive
integer types.
It also includes the 'Bounded' integer wrapping type: an integer
value that requires only the 'N' least significant bits of the
wrapped type to be encoded:
// An unsigned 8-bit integer, of which only the 4 LSBs are used.
let v = Bounded::<u8, 4>::new::<15>();
assert_eq!(v.get(), 15);
'Bounded' is useful to e.g. enforce guarantees when working with
bitfields that have an arbitrary number of bits.
Values can also be constructed from simple non-constant expressions
or, for more complex ones, validated at runtime.
'Bounded' also comes with comparison and arithmetic operations
(with both their backing type and other 'Bounded's with a
compatible backing type), casts to change the backing type,
extending/shrinking and infallible/fallible conversions from/to
primitives as applicable.
It enables to use just an immutable tree reference where
appropriate. The existing fully-featured mutable cursor is renamed
to 'CursorMut'.
kallsyms:
- Fix wrong "big" kernel symbol type read from procfs.
'pin-init' crate:
- A couple minor fixes (Benno asked me to pick these patches up for
him this cycle).
Documentation:
- Quick Start guide: add Debian 13 (Trixie).
Debian Stable is now able to build Linux, since Debian 13 (released
2025-08-09) packages Rust 1.85.0, which is recent enough.
We are planning to propose that the minimum supported Rust version
in Linux follows Debian Stable releases, with Debian 13 being the
first one we upgrade to, i.e. Rust 1.85.
MAINTAINERS:
- Add entry for the new 'num' module.
- Remove Alex as Rust maintainer: he hasn't had the time to
contribute for a few years now, so it is a no-op change in
practice.
And a few other cleanups and improvements"
* tag 'rust-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux: (53 commits)
rust: macros: support `proc-macro2`, `quote` and `syn`
rust: syn: enable support in kbuild
rust: syn: add `README.md`
rust: syn: remove `unicode-ident` dependency
rust: syn: add SPDX License Identifiers
rust: syn: import crate
rust: quote: enable support in kbuild
rust: quote: add `README.md`
rust: quote: add SPDX License Identifiers
rust: quote: import crate
rust: proc-macro2: enable support in kbuild
rust: proc-macro2: add `README.md`
rust: proc-macro2: remove `unicode_ident` dependency
rust: proc-macro2: add SPDX License Identifiers
rust: proc-macro2: import crate
rust: kbuild: support using libraries in `rustc_procmacro`
rust: kbuild: support skipping flags in `rustc_test_library`
rust: kbuild: add proc macro library support
rust: kbuild: simplify `--cfg` handling
rust: kbuild: introduce `core-flags` and `core-skip_flags`
...
Linus Torvalds [Wed, 3 Dec 2025 21:46:48 +0000 (13:46 -0800)]
Merge tag 'livepatching-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching
Pull livepatching updates from Petr Mladek:
- Support both paths where tracefs is typically mounted in selftests
- Make old_sympos 0 and 1 equal. They both are valid when there is only
one symbol with the given name.
* tag 'livepatching-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
selftests: livepatch: use canonical ftrace path
livepatch: Match old_sympos 0 and 1 in klp_find_func()
Linus Torvalds [Wed, 3 Dec 2025 21:25:39 +0000 (13:25 -0800)]
Merge tag 'sched_ext-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext updates from Tejun Heo:
- Improve recovery from misbehaving BPF schedulers.
When a scheduler puts many tasks with varying affinity restrictions
on a shared DSQ, CPUs scanning through tasks they cannot run can
overwhelm the system, causing lockups.
Bypass mode now uses per-CPU DSQs with a load balancer to avoid this,
and hooks into the hardlockup detector to attempt recovery.
Add scx_cpu0 example scheduler to demonstrate this scenario.
- Add lockless peek operation for DSQs to reduce lock contention for
schedulers that need to query queue state during load balancing.
- Allow scx_bpf_reenqueue_local() to be called from anywhere in
preparation for deprecating cpu_acquire/release() callbacks in favor
of generic BPF hooks.
- Prepare for hierarchical scheduler support: add
scx_bpf_task_set_slice() and scx_bpf_task_set_dsq_vtime() kfuncs,
make scx_bpf_dsq_insert*() return bool, and wrap kfunc args in
structs for future aux__prog parameter.
- Implement cgroup_set_idle() callback to notify BPF schedulers when a
cgroup's idle state changes.
- Fix migration tasks being incorrectly downgraded from
stop_sched_class to rt_sched_class across sched_ext enable/disable.
Applied late as the fix is low risk and the bug subtle but needs
stable backporting.
- Various fixes and cleanups including cgroup exit ordering,
SCX_KICK_WAIT reliability, and backward compatibility improvements.
* tag 'sched_ext-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext: (44 commits)
sched_ext: Fix incorrect sched_class settings for per-cpu migration tasks
sched_ext: tools: Removing duplicate targets during non-cross compilation
sched_ext: Use kvfree_rcu() to release per-cpu ksyncs object
sched_ext: Pass locked CPU parameter to scx_hardlockup() and add docs
sched_ext: Update comments replacing breather with aborting mechanism
sched_ext: Implement load balancer for bypass mode
sched_ext: Factor out abbreviated dispatch dequeue into dispatch_dequeue_locked()
sched_ext: Factor out scx_dsq_list_node cursor initialization into INIT_DSQ_LIST_CURSOR
sched_ext: Add scx_cpu0 example scheduler
sched_ext: Hook up hardlockup detector
sched_ext: Make handle_lockup() propagate scx_verror() result
sched_ext: Refactor lockup handlers into handle_lockup()
sched_ext: Make scx_exit() and scx_vexit() return bool
sched_ext: Exit dispatch and move operations immediately when aborting
sched_ext: Simplify breather mechanism with scx_aborting flag
sched_ext: Use per-CPU DSQs instead of per-node global DSQs in bypass mode
sched_ext: Refactor do_enqueue_task() local and global DSQ paths
sched_ext: Use shorter slice in bypass mode
sched_ext: Mark racy bitfields to prevent adding fields that can't tolerate races
sched_ext: Minor cleanups to scx_task_iter
...
Linus Torvalds [Wed, 3 Dec 2025 21:04:07 +0000 (13:04 -0800)]
Merge tag 'cgroup-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- Defer task cgroup unlink until after the dying task's final context
switch so that controllers see the cgroup properly populated until
the task is truly gone
- cpuset cleanups and simplifications.
Enforce that domain isolated CPUs stay in root or isolated partitions
and fail if isolated+nohz_full would leave no housekeeping CPU. Fix
sched/deadline root domain handling during CPU hot-unplug and race
for tasks in attaching cpusets
- Misc fixes including memory reclaim protection documentation and
selftest KTAP conformance
* tag 'cgroup-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
cpuset: Treat cpusets in attaching as populated
sched/deadline: Walk up cpuset hierarchy to decide root domain when hot-unplug
cgroup/cpuset: Introduce cpuset_cpus_allowed_locked()
docs: cgroup: No special handling of unpopulated memcgs
docs: cgroup: Note about sibling relative reclaim protection
docs: cgroup: Explain reclaim protection target
selftests/cgroup: conform test to KTAP format output
cpuset: remove need_rebuild_sched_domains
cpuset: remove global remote_children list
cpuset: simplify node setting on error
cgroup: include missing header for struct irq_work
cgroup: Fix sleeping from invalid context warning on PREEMPT_RT
cgroup/cpuset: Globally track isolated_cpus update
cgroup/cpuset: Ensure domain isolated CPUs stay in root or isolated partition
cgroup/cpuset: Move up prstate_housekeeping_conflict() helper
cgroup/cpuset: Fail if isolated and nohz_full don't leave any housekeeping
cgroup/cpuset: Rename update_unbound_workqueue_cpumask() to update_isolation_cpumasks()
cgroup: Defer task cgroup unlink until after the task is done switching out
cgroup: Move dying_tasks cleanup from cgroup_task_release() to cgroup_task_free()
cgroup: Rename cgroup lifecycle hooks to cgroup_task_*()
...
Linus Torvalds [Wed, 3 Dec 2025 20:50:10 +0000 (12:50 -0800)]
Merge tag 'wq-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue updates from Tejun Heo:
- Rescuer affinity management: Affinity is now updated only when
detached using wq_unbound_cpumask consistently. DISASSOCIATED workers
also follow unbound cpumask changes to avoid breaking CPU isolation
- Rescuer cleanups preparing for fetching work items one by one from
pool list: Work assignment factored out, optimized to skip pwqs no
longer needing rescue, and shutdown logic simplified
* tag 'wq-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Don't rely on wq->rescuer to stop rescuer
workqueue: Only assign rescuer work when really needed
workqueue: Factor out assign_rescuer_work()
workqueue: Init rescuer's affinities as wq_unbound_cpumask
workqueue: Let DISASSOCIATED workers follow unbound wq cpumask changes
workqueue: Update the rescuer's affinity only when it is detached
workqueue: Remove unused assert_rcu_or_wq_mutex_or_pool_mutex
Linus Torvalds [Wed, 3 Dec 2025 20:42:36 +0000 (12:42 -0800)]
Merge tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Allow creaing nbcon console drivers with an unsafe write_atomic()
callback that can only be called by the final nbcon_atomic_flush_unsafe().
Otherwise, the driver would rely on the kthread.
It is going to be used as the-best-effort approach for an
experimental nbcon netconsole driver, see
In an ideal world, all networking drivers would be fixed first and
the atomic flush would be blocked only in NMI context. But it brings
the question how reliable networking drivers are when the system is
in a bad state. They might block flushing more reliable serial
consoles which are more suitable for serious debugging anyway.
- Allow to use the last 4 bytes of the printk ring buffer.
- Prevent queuing IRQ work and block printk kthreads when consoles are
suspended. Otherwise, they create non-necessary churn or even block
the suspend.
- Release console_lock() between each record in the kthread used for
legacy consoles on RT. It might significantly speed up the boot.
- Release nbcon context between each record in the atomic flush. It
prevents stalls of the related printk kthread after it has lost the
ownership in the middle of a record
- Add support for NBCON consoles into KDB
- Add %ptsP modifier for printing struct timespec64 and use it where
possible
- Misc code clean up
* tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (48 commits)
printk: Use console_is_usable on console_unblank
arch: um: kmsg_dump: Use console_is_usable
drivers: serial: kgdboc: Drop checks for CON_ENABLED and CON_BOOT
lib/vsprintf: Unify FORMAT_STATE_NUM handlers
printk: Avoid irq_work for printk_deferred() on suspend
printk: Avoid scheduling irq_work on suspend
printk: Allow printk_trigger_flush() to flush all types
tracing: Switch to use %ptSp
scsi: snic: Switch to use %ptSp
scsi: fnic: Switch to use %ptSp
s390/dasd: Switch to use %ptSp
ptp: ocp: Switch to use %ptSp
pps: Switch to use %ptSp
PCI: epf-test: Switch to use %ptSp
net: dsa: sja1105: Switch to use %ptSp
mmc: mmc_test: Switch to use %ptSp
media: av7110: Switch to use %ptSp
ipmi: Switch to use %ptSp
igb: Switch to use %ptSp
e1000e: Switch to use %ptSp
...
Linus Torvalds [Wed, 3 Dec 2025 20:41:00 +0000 (12:41 -0800)]
Merge tag 'lkmm.2025.12.01a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull lkmm documentation update from Paul McKenney:
- Sort the memory-barriers.txt file's wait_event* and wait_on_bit* list
alphabetically
* tag 'lkmm.2025.12.01a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
memory-barriers.txt: Sort wait_event* and wait_on_bit* list alphabetically
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:45 +0000 (14:18 -0600)]
Merge branch 'pci/pwrctrl-tc9563'
- Add a struct pci_ops.assert_perst() function pointer to assert/deassert
PCIe PERST# and implement it for the qcom driver (Krishna Chaitanya
Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe switch,
which must be held in reset after poweron so the pwrctrl driver can
configure the switch via I2C before bringing up the links (Krishna
Chaitanya Chundru)
* pci/pwrctrl-tc9563:
PCI: pwrctrl: Add power control driver for TC9563
PCI: qcom: Implement .assert_perst()
PCI: dwc: Implement .assert_perst() for dwc glue drivers
PCI: Add .assert_perst() to control PCIe PERST#
dt-bindings: PCI: Add binding for Toshiba TC9563 PCIe switch
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:38 +0000 (14:18 -0600)]
Merge branch 'pci/controller/mediatek'
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian Marangi)
* pci/controller/mediatek:
PCI: mediatek: Add support for Airoha AN7583 SoC
PCI: mediatek: Use generic MACRO for TPVPERL delay
PCI: mediatek: Convert bool to single quirks entry and bitmap
dt-bindings: PCI: mediatek: Add support for Airoha AN7583
dt-bindings: PCI: mediatek: Convert to YAML schema
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:38 +0000 (14:18 -0600)]
Merge branch 'pci/controller/keystone'
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)
* pci/controller/keystone:
PCI: keystone: Add support to build as a loadable module
PCI: dwc: Export dw_pcie_allocate_domains() and dw_pcie_ep_raise_msix_irq()
PCI: Export pci_get_host_bridge_device() for use by pci-keystone
PCI: keystone: Exit ks_pcie_probe() for invalid mode
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:37 +0000 (14:18 -0600)]
Merge branch 'pci/controller/j721e'
- Use devm_clk_get_optional_enabled() instead of open-coding
devm_clk_get_optional() and clk_prepare_enable() (Anand Moon)
* pci/controller/j721e:
PCI: j721e: Use 'pcie->reset_gpio' directly and drop the local variable
PCI: j721e: Use devm_clk_get_optional_enabled() to get and enable the clock
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:35 +0000 (14:18 -0600)]
Merge branch 'pci/controller/dwc'
- Update PORT_LOGIC_LTSSM_STATE_MASK to be a 6-bit mask as per spec, not a
5-bit mask (Shawn Lin)
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver says
it's supported, which prevents users from enabling non-working L1SS.
Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn Helgaas)
- Configure L1SS support in dw-rockchip when DT says 'supports-clkreq'
(Shawn Lin)
* pci/controller/dwc:
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
PCI: dwc: Advertise L1 PM Substates only if driver requests it
PCI: dwc: Fix wrong PORT_LOGIC_LTSSM_STATE_MASK definition
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:35 +0000 (14:18 -0600)]
Merge branch 'pci/controller/brcmstb'
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe caused an
unrecoverable abort (Jim Quinlan)
* pci/controller/brcmstb:
PCI: brcmstb: Add panic/die handler to driver
PCI: brcmstb: Add a way to indicate if PCIe bridge is active
PCI: brcmstb: Fix disabling L0s capability
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:32 +0000 (14:18 -0600)]
Merge branch 'pci/resource'
- Prevent resource tree corruption when BAR resize fails (Ilpo Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and amdgpu
drivers so the PCI core can restore BARs if the resize fails (Ilpo
Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo Järvinen)
* pci/resource:
PCI: Validate pci_rebar_size_supported() input
PCI: Convert BAR sizes bitmasks to u64
drm/amdgpu: Use pci_rebar_get_max_size()
drm/xe/vram: Use pci_rebar_get_max_size()
PCI: Add pci_rebar_get_max_size()
drm/xe/vram: Use PCI rebar helpers in resize_vram_bar()
drm/i915/gt: Use pci_rebar_size_supported()
PCI: Add pci_rebar_size_supported() helper
PCI: Improve Resizable BAR functions kernel doc
PCI: Move pci_rebar_size_to_bytes() and export it
PCI: Move pci_rebar_bytes_to_size() and clean it up
PCI: Move Resizable BAR code to rebar.c
PCI: Prevent restoring assigned resources
drm/amdgpu: Remove driver side BAR release before resize
drm/i915: Remove driver side BAR release before resize
drm/xe: Remove driver side BAR release before resize
PCI: Add kerneldoc for pci_resize_resource()
PCI: Fix restoring BARs on BAR resize rollback path
PCI: Free saved list without holding pci_bus_sem
PCI: Try BAR resize even when no window was released
PCI: Change pci_dev variable from 'bridge' to 'dev'
PCI/IOV: Adjust ->barsz[] when changing BAR size
PCI: Prevent resource tree corruption when BAR resize fails
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:31 +0000 (14:18 -0600)]
Merge branch 'pci/ptm'
- Enable PTM only if device advertises support for a relevant role, to
prevent invalid PTM Requests that cause ACS violations that are reported
as AER Uncorrectable Non-Fatal errors (Mika Westerberg)
* pci/ptm:
PCI/PTM: Enable only if device advertises relevant role
Bjorn Helgaas [Wed, 3 Dec 2025 20:18:31 +0000 (14:18 -0600)]
Merge branch 'pci/err'
- For drivers using PCI legacy suspend, save config state at suspend so
that state (not any earlier state from enumeration, probe, or error
recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks PM, save config state
at hibernate so that state (not any earlier state from enumeration,
probe, or error recovery) will be restored when resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding, so
error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it since
the PCI core always does it and pci_restore_state() no longer invalidates
the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state they
want restored during error recovery (Lukas Wunner)
* pci/err:
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
Linus Torvalds [Wed, 3 Dec 2025 20:18:07 +0000 (12:18 -0800)]
Merge tag 'rcu.release.v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux
Pull RCU updates from Frederic Weisbecker:
"SRCU:
- Properly handle SRCU readers within IRQ disabled sections in tiny
SRCU
- Preparation to reimplement RCU Tasks Trace on top of SRCU fast:
- Introduce API to expedite a grace period and test it through
rcutorture
- Split srcu-fast in two flavours: SRCU-fast and SRCU-fast-updown.
Both are still targeted toward faster readers (without full
barriers on LOCK and UNLOCK) at the expense of heavier write
side (using full RCU grace period ordering instead of simply
full ordering) as compared to "traditional" non-fast SRCU. But
those srcu-fast flavours are going to be optimized in two
different ways:
- SRCU-fast will become the reimplementation basis for
RCU-TASK-TRACE for consolidation. Since RCU-TASK-TRACE must
be NMI safe, SRCU-fast must be as well.
- SRCU-fast-updown will be needed for uretprobes code in order
to get rid of the read-side memory barriers while still
allowing entering the reader at task level while exiting it
in a timer handler. It is considered semaphore-like in that
it can have different owners between LOCK and UNLOCK.
However it is not NMI-safe.
The actual optimizations are work in progress for the next
cycle. Only the new interfaces are added for now, along with
related torture and scalability test code.
- Create/document/debug/torture new proper initializers for RCU fast:
DEFINE_SRCU_FAST() and init_srcu_struct_fast()
This allows for using right away the proper ordering on the write
side (either full ordering or full RCU grace period ordering)
without waiting for the read side to tell which to use.
This also optimizes the read side altogether with moving flavour
debug checks under debug config and with removing a costly RmW
operation on their first call.
- Make some diagnostic functions tracing safe
Refscale:
- Add performance testing for common context synchronizations
(Preemption, IRQ, Softirq) and per-cpu increments. Those are
relevant comparisons against SRCU-fast read side APIs, especially
as they are planned to synchronize further tracing fast-path code
Miscellanous:
- In order to prepare the layout for nohz_full work deferral to user
exit, the context tracking state must shrink the counter of
transitions to/from RCU not watching. The only possible hazard is
to trigger wrap-around more easily, delaying a bit grace periods
when that happens. This should be a rare event though. Yet add
debugging and torture code to test that assumption
- Fix memory leak on locktorture module
- Annotate accesses in rculist_nulls.h to prevent from KCSAN
warnings. On recent discussions, we also concluded that all those
WRITE_ONCE() and READ_ONCE() on list APIs deserve appropriate
comments. Something to be expected for the next cycle
- Provide a script to apply several configs to several commits with
torture
- Allow torture to reuse a build directory in order to save needless
rebuild time
- Various cleanups"
* tag 'rcu.release.v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux: (29 commits)
refscale: Add SRCU-fast-updown readers
refscale: Exercise DEFINE_STATIC_SRCU_FAST() and init_srcu_struct_fast()
rcutorture: Make srcu{,d}_torture_init() announce the SRCU type
srcu: Create an SRCU-fast-updown API
refscale: Do not disable interrupts for tests involving local_bh_enable()
refscale: Add non-atomic per-CPU increment readers
refscale: Add this_cpu_inc() readers
refscale: Add preempt_disable() readers
refscale: Add local_bh_disable() readers
refscale: Add local_irq_disable() and local_irq_save() readers
torture: Permit negative kvm.sh --kconfig numberic arguments
srcu: Add SRCU_READ_FLAVOR_FAST_UPDOWN CPP macro
rcu: Mark diagnostic functions as notrace
rcutorture: Make TREE04 use CONFIG_RCU_DYNTICKS_TORTURE
rcutorture: Remove redundant rcutorture_one_extend() from rcu_torture_one_read()
rcutorture: Permit kvm-again.sh to re-use the build directory
torture: Add kvm-series.sh to test commit/scenario combination
rcu: use WRITE_ONCE() for ->next and ->pprev of hlist_nulls
locktorture: Fix memory leak in param_set_cpumask()
doc: Update for SRCU-fast definitions and initialization
...
Linus Torvalds [Wed, 3 Dec 2025 19:53:47 +0000 (11:53 -0800)]
Merge tag 'slab-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab updates from Vlastimil Babka:
- mempool_alloc_bulk() support for upcoming users in the block layer
that need to allocate multiple objects at once with the mempool's
guaranteed progress semantics, which is not achievable with an
allocation single objects in a loop. Along with refactoring and
various improvements (Christoph Hellwig)
- Preparations for the upcoming separation of struct slab from struct
page, mostly by removing the struct folio layer, as the purpose of
struct folio has shifted since it became used in slab code (Matthew
Wilcox)
- Modernisation of slab's boot param API usage, which removes some
unexpected parsing corner cases (Petr Tesarik)
- Refactoring of freelist_aba_t (now struct freelist_counters) and
associated functions for double cmpxchg, enabled by -fms-extensions
(Vlastimil Babka)
- Cleanups and improvements related to sheaves caching layer, that were
part of the full conversion to sheaves, which is planned for the next
release (Vlastimil Babka)
* tag 'slab-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab: (42 commits)
slab: Remove unnecessary call to compound_head() in alloc_from_pcs()
mempool: clarify behavior of mempool_alloc_preallocated()
mempool: drop the file name in the top of file comment
mempool: de-typedef
mempool: remove mempool_{init,create}_kvmalloc_pool
mempool: legitimize the io_schedule_timeout in mempool_alloc_from_pool
mempool: add mempool_{alloc,free}_bulk
mempool: factor out a mempool_alloc_from_pool helper
slab: Remove references to folios from virt_to_slab()
kasan: Remove references to folio in __kasan_mempool_poison_object()
memcg: Convert mem_cgroup_from_obj_folio() to mem_cgroup_from_obj_slab()
mempool: factor out a mempool_adjust_gfp helper
mempool: add error injection support
mempool: improve kerneldoc comments
mm: improve kerneldoc comments for __alloc_pages_bulk
fault-inject: make enum fault_flags available unconditionally
usercopy: Remove folio references from check_heap_object()
slab: Remove folio references from kfree_nolock()
slab: Remove folio references from kfree_rcu_sheaf()
slab: Remove folio references from build_detached_freelist()
...
Linus Torvalds [Wed, 3 Dec 2025 19:34:28 +0000 (11:34 -0800)]
Merge tag 'docs-6.19' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This has been another busy cycle for documentation, with a lot of
build-system thrashing. That work should slow down from here on out.
- The various scripts and tools for documentation were spread out in
several directories; now they are (almost) all coalesced under
tools/docs/. The holdout is the kernel-doc script, which cannot be
easily moved without some further thought.
- As the amount of Python code increases, we are accumulating modules
that are imported by multiple programs. These modules have been
pulled together under tools/lib/python/ -- at least, for
documentation-related programs. There is other Python code in the
tree that might eventually want to move toward this organization.
- The Perl kernel-doc.pl script has been removed. It is no longer
used by default, and nobody has missed it, least of all anybody who
actually had to look at it.
- The docs build was controlled by a complex mess of makefilese that
few dared to touch. Mauro has moved that logic into a new program
(tools/docs/sphinx-build-wrapper) that, with any luck at all, will
be far easier to understand and maintain.
- The get_feat.pl program, used to access information under
Documentation/features/, has been rewritten in Python, bringing an
end to the use of Perl in the docs subsystem.
- The top-level README file has been reorganized into a more
reader-friendly presentation.
- A lot of Chinese translation additions
- Typo fixes and documentation updates as usual"
* tag 'docs-6.19' of git://git.lwn.net/linux: (164 commits)
docs: makefile: move rustdoc check to the build wrapper
README: restructure with role-based documentation and guidelines
docs: kdoc: various fixes for grammar, spelling, punctuation
docs: kdoc_parser: use '@' for Excess enum value
docs: submitting-patches: Clarify that removal of Acks needs explanation too
docs: kdoc_parser: add data/function attributes to ignore
docs: MAINTAINERS: update Mauro's files/paths
docs/zh_CN: Add wd719x.rst translation
docs/zh_CN: Add libsas.rst translation
get_feat.pl: remove it, as it got replaced by get_feat.py
Documentation/sphinx/kernel_feat.py: use class directly
tools/docs/get_feat.py: convert get_feat.pl to Python
Documentation/admin-guide: fix typo and comment in cscope example
docs/zh_CN: Add data-integrity.rst translation
docs/zh_CN: Add blk-mq.rst translation
docs/zh_CN: Add block/index.rst translation
docs/zh_CN: Update the Chinese translation of kbuild.rst
docs: bring some order to our Python module hierarchy
docs: Move the python libraries to tools/lib/python
Documentation/kernel-parameters: Move the kernel build options
...
Linus Torvalds [Wed, 3 Dec 2025 19:28:38 +0000 (11:28 -0800)]
Merge tag 'v6.19-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Rewrite memcpy_sglist from scratch
- Add on-stack AEAD request allocation
- Fix partial block processing in ahash
Algorithms:
- Remove ansi_cprng
- Remove tcrypt tests for poly1305
- Fix EINPROGRESS processing in authenc
- Fix double-free in zstd
Drivers:
- Use drbg ctr helper when reseeding xilinx-trng
- Add support for PCI device 0x115A to ccp
- Add support of paes in caam
- Add support for aes-xts in dthev2
Others:
- Use likely in rhashtable lookup
- Fix lockdep false-positive in padata by removing a helper"
* tag 'v6.19-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (71 commits)
crypto: zstd - fix double-free in per-CPU stream cleanup
crypto: ahash - Zero positive err value in ahash_update_finish
crypto: ahash - Fix crypto_ahash_import with partial block data
crypto: lib/mpi - use min() instead of min_t()
crypto: ccp - use min() instead of min_t()
hwrng: core - use min3() instead of nested min_t()
crypto: aesni - ctr_crypt() use min() instead of min_t()
crypto: drbg - Delete unused ctx from struct sdesc
crypto: testmgr - Add missing DES weak and semi-weak key tests
Revert "crypto: scatterwalk - Move skcipher walk and use it for memcpy_sglist"
crypto: scatterwalk - Fix memcpy_sglist() to always succeed
crypto: iaa - Request to add Kanchana P Sridhar to Maintainers.
crypto: tcrypt - Remove unused poly1305 support
crypto: ansi_cprng - Remove unused ansi_cprng algorithm
crypto: asymmetric_keys - fix uninitialized pointers with free attribute
KEYS: Avoid -Wflex-array-member-not-at-end warning
crypto: ccree - Correctly handle return of sg_nents_for_len
crypto: starfive - Correctly handle return of sg_nents_for_len
crypto: iaa - Fix incorrect return value in save_iaa_wq()
crypto: zstd - Remove unnecessary size_t cast
...
Linus Torvalds [Wed, 3 Dec 2025 19:19:34 +0000 (11:19 -0800)]
Merge tag 'ipe-pr-20251202' of git://git.kernel.org/pub/scm/linux/kernel/git/wufan/ipe
Pull IPE udates from Fan Wu:
"The primary change is the addition of support for the AT_EXECVE_CHECK
flag. This allows interpreters to signal the kernel to perform IPE
security checks on script files before execution, extending IPE
enforcement to indirectly executed scripts.
Update documentation for it, and also fix a comment"
* tag 'ipe-pr-20251202' of git://git.kernel.org/pub/scm/linux/kernel/git/wufan/ipe:
ipe: Update documentation for script enforcement
ipe: Add AT_EXECVE_CHECK support for script enforcement
ipe: Drop a duplicated CONFIG_ prefix in the ifdeffery
Linus Torvalds [Wed, 3 Dec 2025 19:08:03 +0000 (11:08 -0800)]
Merge tag 'integrity-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"Bug fixes:
- defer credentials checking from the bprm_check_security hook to the
bprm_creds_from_file security hook
- properly ignore IMA policy rules based on undefined SELinux labels
IMA policy rule extensions:
- extend IMA to limit including file hashes in the audit logs
(dont_audit action)
- define a new filesystem subtype policy option (fs_subtype)
Misc:
- extend IMA to support in-kernel module decompression by deferring
the IMA signature verification in kernel_read_file() to after the
kernel module is decompressed"
* tag 'integrity-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: Handle error code returned by ima_filter_rule_match()
ima: Access decompressed kernel module to verify appended signature
ima: add fs_subtype condition for distinguishing FUSE instances
ima: add dont_audit action to suppress audit actions
ima: Attach CREDS_CHECK IMA hook to bprm_creds_from_file LSM hook
Linus Torvalds [Wed, 3 Dec 2025 18:52:01 +0000 (10:52 -0800)]
Merge tag 'audit-pr-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
- Consolidate the loops in __audit_inode_child() to improve performance
When logging a child inode in __audit_inode_child(), we first run
through the list of recorded inodes looking for the parent and then
we repeat the search looking for a matching child entry. This pull
request consolidates both searches into one pass through the recorded
inodes, resuling in approximately a 50% reduction in audit overhead.
See the commit description for the testing details.
- Combine kmalloc()/memset() into kzalloc() in audit_krule_to_data()
- Comment fixes
* tag 'audit-pr-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: merge loops in __audit_inode_child()
audit: Use kzalloc() instead of kmalloc()/memset() in audit_krule_to_data()
audit: fix comment misindentation in audit.h
Linus Torvalds [Wed, 3 Dec 2025 18:45:47 +0000 (10:45 -0800)]
Merge tag 'selinux-pr-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
- Improve the granularity of SELinux labeling for memfd files
Currently when creating a memfd file, SELinux treats it the same as
any other tmpfs, or hugetlbfs, file. While simple, the drawback is
that it is not possible to differentiate between memfd and tmpfs
files.
This adds a call to the security_inode_init_security_anon() LSM hook
and wires up SELinux to provide a set of memfd specific access
controls, including the ability to control the execution of memfds.
As usual, the commit message has more information.
- Improve the SELinux AVC lookup performance
Adopt MurmurHash3 for the SELinux AVC hash function instead of the
custom hash function currently used. MurmurHash3 is already used for
the SELinux access vector table so the impact to the code is minimal,
and performance tests have shown improvements in both hash
distribution and latency.
See the commit message for the performance measurments.
- Introduce a Kconfig option for the SELinux AVC bucket/slot size
While we have the ability to grow the number of AVC hash buckets
today, the size of the buckets (slot size) is fixed at 512. This pull
request makes that slot size configurable at build time through a new
Kconfig knob, CONFIG_SECURITY_SELINUX_AVC_HASH_BITS.
* tag 'selinux-pr-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: improve bucket distribution uniformity of avc_hash()
selinux: Move avtab_hash() to a shared location for future reuse
selinux: Introduce a new config to make avc cache slot size adjustable
memfd,selinux: call security_inode_init_security_anon()
Linus Torvalds [Wed, 3 Dec 2025 17:53:48 +0000 (09:53 -0800)]
Merge tag 'lsm-pr-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull LSM updates from Paul Moore:
- Rework the LSM initialization code
What started as a "quick" patch to enable a notification event once
all of the individual LSMs were initialized, snowballed a bit into a
30+ patch patchset when everything was done. Most of the patches, and
diffstat, is due to splitting out the initialization code into
security/lsm_init.c and cleaning up some of the mess that was there.
While not strictly necessary, it does cleanup the code signficantly,
and hopefully makes the upkeep a bit easier in the future.
Aside from the new LSM_STARTED_ALL notification, these changes also
ensure that individual LSM initcalls are only called when the LSM is
enabled at boot time. There should be a minor reduction in boot times
for those who build multiple LSMs into their kernels, but only enable
a subset at boot.
It is worth mentioning that nothing at present makes use of the
LSM_STARTED_ALL notification, but there is work in progress which is
dependent upon LSM_STARTED_ALL.
- Make better use of the seq_put*() helpers in device_cgroup
* tag 'lsm-pr-20251201' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm: (36 commits)
lsm: use unrcu_pointer() for current->cred in security_init()
device_cgroup: Refactor devcgroup_seq_show to use seq_put* helpers
lsm: add a LSM_STARTED_ALL notification event
lsm: consolidate all of the LSM framework initcalls
selinux: move initcalls to the LSM framework
ima,evm: move initcalls to the LSM framework
lockdown: move initcalls to the LSM framework
apparmor: move initcalls to the LSM framework
safesetid: move initcalls to the LSM framework
tomoyo: move initcalls to the LSM framework
smack: move initcalls to the LSM framework
ipe: move initcalls to the LSM framework
loadpin: move initcalls to the LSM framework
lsm: introduce an initcall mechanism into the LSM framework
lsm: group lsm_order_parse() with the other lsm_order_*() functions
lsm: output available LSMs when debugging
lsm: cleanup the debug and console output in lsm_init.c
lsm: add/tweak function header comment blocks in lsm_init.c
lsm: fold lsm_init_ordered() into security_init()
lsm: cleanup initialize_lsm() and rename to lsm_init_single()
...
Linus Torvalds [Wed, 3 Dec 2025 17:45:23 +0000 (09:45 -0800)]
Merge tag 'keys-trusted-next-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull trusted key updates from Jarkko Sakkinen:
- Remove duplicate 'tpm2_hash_map' in favor of 'tpm2_find_hash_alg()'
- Fix a memory leak on failure paths of 'tpm2_load_cmd'
* tag 'keys-trusted-next-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
KEYS: trusted: Fix a memory leak in tpm2_load_cmd
KEYS: trusted: Replace a redundant instance of tpm2_hash_map
Linus Torvalds [Wed, 3 Dec 2025 17:41:04 +0000 (09:41 -0800)]
Merge tag 'keys-next-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull keys update from Jarkko Sakkinen:
"This contains only three fixes"
* tag 'keys-next-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
keys: Fix grammar and formatting in 'struct key_type' comments
keys: Replace deprecated strncpy in ecryptfs_fill_auth_tok
keys: Remove redundant less-than-zero checks
Linus Torvalds [Wed, 3 Dec 2025 17:23:25 +0000 (09:23 -0800)]
Merge tag 'nolibc-20251130-for-6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/nolibc/linux-nolibc
Pull nolibc updates from Thomas Weißschuh:
- Preparations to the use of nolibc in UML:
- Cleanup of sparse warnings
- Library mode without _start()
- More consistency when disabling errno
- Unconditional installation of all architecture support files
- Always 64-bit wide ino_t and off_t
- Various cleanups and bug fixes
* tag 'nolibc-20251130-for-6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/nolibc/linux-nolibc: (25 commits)
selftests/nolibc: error out on linker warnings
selftests/nolibc: use lld to link loongarch binaries
tools/nolibc: remove more __nolibc_enosys() fallbacks
tools/nolibc: remove now superfluous overflow check in llseek
tools/nolibc: use 64-bit off_t
tools/nolibc: prefer the llseek syscall
tools/nolibc: handle 64-bit off_t for llseek
tools/nolibc: use 64-bit ino_t
tools/nolibc: avoid using plain integer as NULL pointer
tools/nolibc: add support for fchdir()
tools/nolibc: clean up outdated comments in generic arch.h
tools/nolibc: make the "headers" target install all supported archs
tools/nolibc: add the more portable inttypes.h
tools/nolibc: provide the portable sys/select.h
tools/nolibc: add missing memchr() to string.h
tools/nolibc: fix misleading help message regarding installation path
tools/nolibc: add uio.h with readv and writev
tools/nolibc: add option to disable runtime
tools/nolibc: use __fallthrough__ rather than fallthrough
tools/nolibc: implement %m if errno is not defined
...
dt-bindings: thermal: qcom-tsens: Remove invalid tab character
Commit 1ee90870ce79 ("dt-bindings: thermal: tsens: Add QCS8300
compatible") uses a tab character which is illegal in YAML (at the
beginning of a line). The original patch was correct, so this got
corrupted when applied.
Extracting empty examples results in just the empty template being
generated and then validated. That's pointless and not free, so filter
out the schemas without any examples from the targets.
There's currently a little less than 10% of the binding schema files
without examples. Removing them improves the build time by ~6%.
Yanzhu Huang [Wed, 5 Nov 2025 23:26:15 +0000 (23:26 +0000)]
ipe: Update documentation for script enforcement
This patch adds explanation of script enforcement mechanism in admin
guide documentation. Describes how IPE supports integrity enforcement
for indirectly executed scripts through the AT_EXECVE_CHECK flag, and
how this differs from kernel enforcement for compiled executables.
Signed-off-by: Yanzhu Huang <yanzhuhuang@linux.microsoft.com> Signed-off-by: Fan Wu <wufan@kernel.org>
Yanzhu Huang [Wed, 5 Nov 2025 23:26:14 +0000 (23:26 +0000)]
ipe: Add AT_EXECVE_CHECK support for script enforcement
This patch adds a new ipe_bprm_creds_for_exec() hook that integrates
with the AT_EXECVE_CHECK mechanism. To enable script enforcement,
interpreters need to incorporate the AT_EXECVE_CHECK flag when
calling execveat() on script files before execution.
When a userspace interpreter calls execveat() with the AT_EXECVE_CHECK
flag, this hook triggers IPE policy evaluation on the script file. The
hook only triggers IPE when bprm->is_check is true, ensuring it's
being called from an AT_EXECVE_CHECK context. It then builds an
evaluation context for an IPE_OP_EXEC operation and invokes IPE policy.
The kernel returns the policy decision to the interpreter, which can
then decide whether to proceed with script execution.
This extends IPE enforcement to indirectly executed scripts, permitting
trusted scripts to execute while denying untrusted ones.
Signed-off-by: Yanzhu Huang <yanzhuhuang@linux.microsoft.com> Signed-off-by: Fan Wu <wufan@kernel.org>
Linus Torvalds [Wed, 3 Dec 2025 03:00:26 +0000 (19:00 -0800)]
Merge tag 'random-6.19-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Dynamically allocate cpumasks off of the stack if the kernel is
configured for a lot of CPUs, to handle a -Wframe-larger-than case
- The removal of next_pseudo_random32() after the last user was
switched over to the prandom interface
- The removal of get_random_u{8,16,32,64}_wait() functions, as there
were no users of those at all
- Some house keeping changes - a few grammar cleanups in the
comments, system_unbound_wq was renamed to system_dfl_wq, and
static_key_initialized no longer needs to be checked
* tag 'random-6.19-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: complete sentence of comment
random: drop check for static_key_initialized
random: remove unused get_random_var_wait functions
random: replace use of system_unbound_wq with system_dfl_wq
random: use offstack cpumask when necessary
prandom: remove next_pseudo_random32
media: vivid: use prandom
random: add missing words in function comments
Linus Torvalds [Wed, 3 Dec 2025 02:53:50 +0000 (18:53 -0800)]
Merge tag 'fpsimd-on-stack-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull arm64 FPSIMD on-stack buffer updates from Eric Biggers:
"This is a core arm64 change. However, I was asked to take this because
most uses of kernel-mode FPSIMD are in crypto or CRC code.
In v6.8, the size of task_struct on arm64 increased by 528 bytes due
to the new 'kernel_fpsimd_state' field. This field was added to allow
kernel-mode FPSIMD code to be preempted.
Unfortunately, 528 bytes is kind of a lot for task_struct. This
regression in the task_struct size was noticed and reported.
Recover that space by making this state be allocated on the stack at
the beginning of each kernel-mode FPSIMD section.
To make it easier for all the users of kernel-mode FPSIMD to do that
correctly, introduce and use a 'scoped_ksimd' abstraction"
* tag 'fpsimd-on-stack-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (23 commits)
lib/crypto: arm64: Move remaining algorithms to scoped ksimd API
lib/crypto: arm/blake2b: Move to scoped ksimd API
arm64/fpsimd: Allocate kernel mode FP/SIMD buffers on the stack
arm64/fpu: Enforce task-context only for generic kernel mode FPU
net/mlx5: Switch to more abstract scoped ksimd guard API on arm64
arm64/xorblocks: Switch to 'ksimd' scoped guard API
crypto/arm64: sm4 - Switch to 'ksimd' scoped guard API
crypto/arm64: sm3 - Switch to 'ksimd' scoped guard API
crypto/arm64: sha3 - Switch to 'ksimd' scoped guard API
crypto/arm64: polyval - Switch to 'ksimd' scoped guard API
crypto/arm64: nhpoly1305 - Switch to 'ksimd' scoped guard API
crypto/arm64: aes-gcm - Switch to 'ksimd' scoped guard API
crypto/arm64: aes-blk - Switch to 'ksimd' scoped guard API
crypto/arm64: aes-ccm - Switch to 'ksimd' scoped guard API
raid6: Move to more abstract 'ksimd' guard API
crypto: aegis128-neon - Move to more abstract 'ksimd' guard API
crypto/arm64: sm4-ce-gcm - Avoid pointless yield of the NEON unit
crypto/arm64: sm4-ce-ccm - Avoid pointless yield of the NEON unit
crypto/arm64: aes-ce-ccm - Avoid pointless yield of the NEON unit
lib/crc: Switch ARM and arm64 to 'ksimd' scoped guard API
...
Linus Torvalds [Wed, 3 Dec 2025 02:26:54 +0000 (18:26 -0800)]
Merge tag 'libcrypto-at-least-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull 'at_least' array size update from Eric Biggers:
"C supports lower bounds on the sizes of array parameters, using the
static keyword as follows: 'void f(int a[static 32]);'. This allows
the compiler to warn about a too-small array being passed.
As discussed, this reuse of the 'static' keyword, while standard, is a
bit obscure. Therefore, add an alias 'at_least' to compiler_types.h.
Then, add this 'at_least' annotation to the array parameters of
various crypto library functions"
* tag 'libcrypto-at-least-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: sha2: Add at_least decoration to fixed-size array params
lib/crypto: sha1: Add at_least decoration to fixed-size array params
lib/crypto: poly1305: Add at_least decoration to fixed-size array params
lib/crypto: md5: Add at_least decoration to fixed-size array params
lib/crypto: curve25519: Add at_least decoration to fixed-size array params
lib/crypto: chacha: Add at_least decoration to fixed-size array params
lib/crypto: chacha20poly1305: Statically check fixed array lengths
compiler_types: introduce at_least parameter decoration pseudo keyword
wifi: iwlwifi: trans: rename at_least variable to min_mode
Linus Torvalds [Wed, 3 Dec 2025 02:24:35 +0000 (18:24 -0800)]
Merge tag 'aes-gcm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull AES-GCM optimizations from Eric Biggers:
"More optimizations and cleanups for the x86_64 AES-GCM code:
- Add a VAES+AVX2 optimized implementation of AES-GCM. This is very
helpful on CPUs that have VAES but not AVX512, such as AMD Zen 3.
- Make the VAES+AVX512 optimized implementation of AES-GCM handle
large amounts of associated data efficiently.
- Remove the "avx10_256" implementation of AES-GCM. It's superseded
by the VAES+AVX2 optimized implementation.
- Rename the "avx10_512" implementation to "avx512"
Overall, this fills in a gap where AES-GCM wasn't fully optimized on
some recent CPUs. It also drops code that won't be as useful as
initially expected due to AVX10/256 being dropped from the AVX10 spec"
* tag 'aes-gcm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
crypto: x86/aes-gcm-vaes-avx2 - initialize full %rax return register
crypto: x86/aes-gcm - optimize long AAD processing with AVX512
crypto: x86/aes-gcm - optimize AVX512 precomputation of H^2 from H^1
crypto: x86/aes-gcm - revise some comments in AVX512 code
crypto: x86/aes-gcm - reorder AVX512 precompute and aad_update functions
crypto: x86/aes-gcm - clean up AVX512 code to assume 512-bit vectors
crypto: x86/aes-gcm - rename avx10 and avx10_512 to avx512
crypto: x86/aes-gcm - remove VAES+AVX10/256 optimized code
crypto: x86/aes-gcm - add VAES+AVX2 optimized code
Linus Torvalds [Wed, 3 Dec 2025 02:20:06 +0000 (18:20 -0800)]
Merge tag 'libcrypto-tests-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library test updates from Eric Biggers:
- Add KUnit test suites for SHA-3, BLAKE2b, and POLYVAL. These are the
algorithms that have new crypto library interfaces this cycle.
- Remove the crypto_shash POLYVAL tests. They're no longer needed
because POLYVAL support was removed from crypto_shash. Better POLYVAL
test coverage is now provided via the KUnit test suite.
* tag 'libcrypto-tests-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
crypto: testmgr - Remove polyval tests
lib/crypto: tests: Add KUnit tests for POLYVAL
lib/crypto: tests: Add additional SHAKE tests
lib/crypto: tests: Add SHA3 kunit tests
lib/crypto: tests: Add KUnit tests for BLAKE2b
Linus Torvalds [Wed, 3 Dec 2025 02:01:03 +0000 (18:01 -0800)]
Merge tag 'libcrypto-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library updates from Eric Biggers:
"This is the main crypto library pull request for 6.19. It includes:
- Add SHA-3 support to lib/crypto/, including support for both the
hash functions and the extendable-output functions. Reimplement the
existing SHA-3 crypto_shash support on top of the library.
This is motivated mainly by the upcoming support for the ML-DSA
signature algorithm, which needs the SHAKE128 and SHAKE256
functions. But even on its own it's a useful cleanup.
This also fixes the longstanding issue where the
architecture-optimized SHA-3 code was disabled by default.
- Add BLAKE2b support to lib/crypto/, and reimplement the existing
BLAKE2b crypto_shash support on top of the library.
This is motivated mainly by btrfs, which supports BLAKE2b
checksums. With this change, all btrfs checksum algorithms now have
library APIs. btrfs is planned to start just using the library
directly.
This refactor also improves consistency between the BLAKE2b code
and BLAKE2s code. And as usual, it also fixes the issue where the
architecture-optimized BLAKE2b code was disabled by default.
- Add POLYVAL support to lib/crypto/, replacing the existing POLYVAL
support in crypto_shash. Reimplement HCTR2 on top of the library.
This simplifies the code and improves HCTR2 performance. As usual,
it also makes the architecture-optimized code be enabled by
default. The generic implementation of POLYVAL is greatly improved
as well.
- Clean up the BLAKE2s code
- Add FIPS self-tests for SHA-1, SHA-2, and SHA-3"
* tag 'libcrypto-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (37 commits)
fscrypt: Drop obsolete recommendation to enable optimized POLYVAL
crypto: polyval - Remove the polyval crypto_shash
crypto: hctr2 - Convert to use POLYVAL library
lib/crypto: x86/polyval: Migrate optimized code into library
lib/crypto: arm64/polyval: Migrate optimized code into library
lib/crypto: polyval: Add POLYVAL library
crypto: polyval - Rename conflicting functions
lib/crypto: x86/blake2s: Use vpternlogd for 3-input XORs
lib/crypto: x86/blake2s: Avoid writing back unchanged 'f' value
lib/crypto: x86/blake2s: Improve readability
lib/crypto: x86/blake2s: Use local labels for data
lib/crypto: x86/blake2s: Drop check for nblocks == 0
lib/crypto: x86/blake2s: Fix 32-bit arg treated as 64-bit
lib/crypto: arm, arm64: Drop filenames from file comments
lib/crypto: arm/blake2s: Fix some comments
crypto: s390/sha3 - Remove superseded SHA-3 code
crypto: sha3 - Reimplement using library API
crypto: jitterentropy - Use default sha3 implementation
lib/crypto: s390/sha3: Add optimized one-shot SHA-3 digest functions
lib/crypto: sha3: Support arch overrides of one-shot digest functions
...
Linus Torvalds [Wed, 3 Dec 2025 01:49:12 +0000 (17:49 -0800)]
Merge tag 'thermal-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These add Nova Lake processor support to the Intel thermal drivers and
DPTF code, update thermal control documentation, simplify the ACPI
DPTF code related to thermal control, add QCS8300 compatible to the
tsens thermal DT bindings, add DT bindings for NXP i.MX91 thermal
module and add support for it to the imx91 thermal driver, update a
few other thermal drivers and fix a format string issue in a thermal
utility:
- Add Nova Lake processor thermal device to the int340x
processor_thermal driver, add DLVR support for Nova Lake to it, add
Nova Lake support to the ACPI DPTF code, document thermal
throttling on Intel platforms, and update workload type hint
interface documentation (Srinivas Pandruvada)
- Remove int340x thermal scan handler from the ACPI DPTF code because
it turned out to be unnecessary (Slawomir Rosek)
- Clean up the Intel int340x thermal driver (Kaushlendra Kumar)
- Document the RZ/V2H TSU DT bindings (Ovidiu Panait)
- Document the Kaanapali Temperature Sensor (Manaf Meethalavalappu
Pallikunhi)
- Document R-Car Gen4 and RZ/G2 support in driver comment (Marek
Vasut)
- Convert to DEFINE_SIMPLE_DEV_PM_OPS() in R-Car [Gen3] (Geert
Uytterhoeven)
- Fix format string bug in thermal-engine (Malaya Kumar Rout)
- Make ipq5018 tsens standalone compatible (George Moussalem)
- Add the QCS8300 compatible for QCom Tsens (Gaurav Kohli)
- Add support for the NXP i.MX91 thermal module, including the DT
bindings (Pengfei Li)"
* tag 'thermal-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/drivers/imx91: Add support for i.MX91 thermal monitoring unit
dt-bindings: thermal: fsl,imx91-tmu: add bindings for NXP i.MX91 thermal module
dt-bindings: thermal: tsens: Add QCS8300 compatible
dt-bindings: thermal: qcom-tsens: make ipq5018 tsens standalone compatible
tools/thermal/thermal-engine: Fix format string bug in thermal-engine
docs: driver-api/thermal/intel_dptf: Add new workload type hint
thermal/drivers/rcar_gen3: Convert to DEFINE_SIMPLE_DEV_PM_OPS()
thermal/drivers/rcar: Convert to DEFINE_SIMPLE_DEV_PM_OPS()
Documentation: thermal: Document thermal throttling on Intel platforms
ACPI: DPTF: Support Nova Lake
thermal: intel: int340x: Add DLVR support for Nova Lake
thermal: int340x: processor_thermal: Add Nova Lake processor thermal device
thermal: intel: int340x: Replace sprintf() with sysfs_emit()
thermal: intel: int340x: Use symbolic constant for UUID comparison
thermal/drivers/rcar_gen3: Document R-Car Gen4 and RZ/G2 support in driver comment
dt-bindings: thermal: qcom-tsens: document the Kaanapali Temperature Sensor
dt-bindings: thermal: r9a09g047-tsu: Document RZ/V2H TSU
ACPI: DPTF: Remove int340x thermal scan handler
thermal: intel: Select INT340X_THERMAL from INTEL_SOC_DTS_THERMAL
Linus Torvalds [Wed, 3 Dec 2025 01:31:22 +0000 (17:31 -0800)]
Merge tag 'pm-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are quite a few interesting things here, including new hardware
support, new features, some bug fixes and documentation updates. In
addition, there are a usual bunch of minor fixes and cleanups all
over.
In the new hardware support category, there are intel_pstate and
intel_rapl driver updates to support new processors, Panther Lake,
Wildcat Lake, Noval Lake, and Diamond Rapids in the OOB mode, OPP and
bandwidth allocation support in the tegra186 cpufreq driver, and
JH7110S SOC support in dt-platdev cpufreq.
The new features are the PM QoS CPU latency limit for suspend-to-idle,
the netlink support for the energy model management, support for
terminating system suspend via a wakeup event during the sync of file
systems, configurable number of hibernation compression threads, the
runtime PM auto-cleanup macros, and the "poweroff" PM event that is
expected to be used during system shutdown.
Bugs are mostly fixed in cpuidle governors, but there are also fixes
elsewhere, like in the amd-pstate cpufreq driver.
Documentation updates include, but are not limited to, a new doc on
debugging shutdown hangs, cross-referencing fixes and cleanups in the
intel_pstate documentation, and updates of comments in the core
hibernation code.
Specifics:
- Introduce and document a QoS limit on CPU exit latency during
wakeup from suspend-to-idle (Ulf Hansson)
- Add support for building libcpupower statically (Zuo An)
- Add support for sending netlink notifications to user space on
energy model updates (Changwoo Mini, Peng Fan)
- Minor improvements to the Rust OPP interface (Tamir Duberstein)
- Fixes to scope-based pointers in the OPP library (Viresh Kumar)
- Use residency threshold in polling state override decisions in the
menu cpuidle governor (Aboorva Devarajan)
- Add sanity check for exit latency and target residency in the
cpufreq core (Rafael Wysocki)
- Use this_cpu_ptr() where possible in the teo governor (Christian
Loehle)
- Rework the handling of tick wakeups in the teo cpuidle governor to
increase the likelihood of stopping the scheduler tick in the cases
when tick wakeups can be counted as non-timer ones (Rafael Wysocki)
- Fix a reverse condition in the teo cpuidle governor and drop a
misguided target residency check from it (Rafael Wysocki)
- Clean up multiple minor defects in the teo cpuidle governor (Rafael
Wysocki)
- Update header inclusion to make it follow the Include What You Use
principle (Andy Shevchenko)
- Enable MSR-based RAPL PMU support in the intel_rapl power capping
driver and arrange for using it on the Panther Lake and Wildcat
Lake processors (Kuppuswamy Sathyanarayanan)
- Add support for Nova Lake and Wildcat Lake processors to the
intel_rapl power capping driver (Kaushlendra Kumar, Srinivas
Pandruvada)
- Add OPP and bandwidth support for Tegra186 (Aaron Kling)
- Optimizations for parameter array handling in the amd-pstate
cpufreq driver (Mario Limonciello)
- Fix for mode changes with offline CPUs in the amd-pstate cpufreq
driver (Gautham Shenoy)
- Preserve freq_table_sorted across suspend/hibernate in the cpufreq
core (Zihuan Zhang)
- Adjust energy model rules for Intel hybrid platforms in the
intel_pstate cpufreq driver and improve printing of debug messages
in it (Rafael Wysocki)
- Replace deprecated strcpy() in cpufreq_unregister_governor()
(Thorsten Blum)
- Fix duplicate hyperlink target errors in the intel_pstate cpufreq
driver documentation and use :ref: directive for internal linking
in it (Swaraj Gaikwad, Bagas Sanjaya)
- Add Diamond Rapids OOB mode support to the intel_pstate cpufreq
driver (Kuppuswamy Sathyanarayanan)
- Use mutex guard for driver locking in the intel_pstate driver and
eliminate some code duplication from it (Rafael Wysocki)
- Replace udelay() with usleep_range() in ACPI cpufreq (Kaushlendra
Kumar)
- Minor improvements to various cpufreq drivers (Christian Marangi,
Hal Feng, Jie Zhan, Marco Crivellari, Miaoqian Lin, and Shuhao Fu)
- Replace snprintf() with scnprintf() in show_trace_dev_match()
(Kaushlendra Kumar)
- Fix typos in runtime.c comments (Malaya Kumar Rout)
- Move governor.h from devfreq under include/linux/ and rename to
devfreq-governor.h to allow devfreq governor definitions in out of
drivers/devfreq/ (Dmitry Baryshkov)
- Use min() to improve readability in tegra30-devfreq.c (Thorsten
Blum)
- Fix potential use-after-free issue of OPP handling in
hisi_uncore_freq.c (Pengjie Zhang)
- Fix typo in DFSO_DOWNDIFFERENTIAL macro name in
governor_simpleondemand.c in devfreq (Riwen Lu)"
* tag 'pm-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (96 commits)
PM / devfreq: Fix typo in DFSO_DOWNDIFFERENTIAL macro name
cpuidle: Warn instead of bailing out if target residency check fails
cpuidle: Update header inclusion
Documentation: power/cpuidle: Document the CPU system wakeup latency QoS
cpuidle: Respect the CPU system wakeup QoS limit for cpuidle
sched: idle: Respect the CPU system wakeup QoS limit for s2idle
pmdomain: Respect the CPU system wakeup QoS limit for cpuidle
pmdomain: Respect the CPU system wakeup QoS limit for s2idle
PM: QoS: Introduce a CPU system wakeup QoS limit
cpuidle: governors: teo: Add missing space to the description
PM: hibernate: Extra cleanup of comments in swap handling code
PM / devfreq: tegra30: use min to simplify actmon_cpu_to_emc_rate
PM / devfreq: hisi: Fix potential UAF in OPP handling
PM / devfreq: Move governor.h to a public header location
powercap: intel_rapl: Enable MSR-based RAPL PMU support
powercap: intel_rapl: Prepare read_raw() interface for atomic-context callers
cpufreq: qcom-nvmem: fix compilation warning for qcom_cpufreq_ipq806x_match_list
PM: sleep: Call pm_sleep_fs_sync() instead of ksys_sync_helper()
PM: sleep: Add support for wakeup during filesystem sync
cpufreq: ACPI: Replace udelay() with usleep_range()
...
Linus Torvalds [Wed, 3 Dec 2025 01:24:03 +0000 (17:24 -0800)]
Merge tag 'acpi-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These add Microsoft fan extensions support to the ACPI fan driver, fix
a bug in ACPICA, update other ACPI drivers (processor, time and alarm
device), update ACPI power management code and ACPI device properties
management, and fix an ACPI utility:
- Avoid walking the ACPI namespace in the AML interpreter if the
starting node cannot be determined (Cryolitia PukNgae)
- Use min() instead of min_t() in the ACPI device properties handling
code to avoid discarding significant bits (David Laight)
- Fix potential fwnode refcount leak in
acpi_fwnode_graph_parse_endpoint() that may prevent the parent
fwnode from being released (Haotian Zhang)
- Rework acpi_graph_get_next_endpoint() to use ACPI functions only,
remove unnecessary conditionals from it to make it easier to
follow, and make acpi_get_next_subnode() static (Sakari Ailus)
- Drop unused function acpi_get_lps0_constraint(), make some
Low-Power S0 callback functions for suspend-to-idle static, and
rearrange the code retrieving Low-Power S0 constraints so it only
runs when the constraints are actually used (Rafael Wysocki)
- Drop redundant locking from the ACPI battery driver (Rafael
Wysocki)
- Improve runtime PM in the ACPI time and alarm device (TAD) driver
using guard macros and rearrange code related to runtime PM in
acpi_tad_remove() (Rafael Wysocki)
- Add support for Microsoft fan extensions to the ACPI fan driver
along with notification support and work around a 64-bit firmware
bug in that driver (Armin Wolf)
- Use ACPI_FREE() to free ACPI buffer in the ACPI DPTF code
(Kaushlendra Kumar)
- Fix a memory leak and a resource leak in the ACPI pfrut utility
(Malaya Kumar Rout)
- Replace `core::mem::zeroed` with `pin_init::zeroed` in the ACPI
Rust code (Siyuan Huang)
- Update the ACPI code to use the new style of allocating workqueues
and new global workqueues (Marco Crivellari)
- Fix two spelling mistakes in the ACPI code (Chu Guangqing)
- Fix ISAPNP to generate uevents to auto-load modules (René Rebe)
- Relocate the state flags initialization in the ACPI processor idle
driver and drop redundant C-state count checks from it (Huisong Li)
- Fix map_x2apic_id() in the ACPI processor core driver for
amd-pstate on am4 (René Rebe)"
* tag 'acpi-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (30 commits)
ACPI: PM: Fix a spelling mistake
ACPI: LPSS: Fix a spelling mistake
ACPI: processor_core: fix map_x2apic_id for amd-pstate on am4
ACPICA: Avoid walking the Namespace if start_node is NULL
ACPI: tools: pfrut: fix memory leak and resource leak in pfrut.c
ACPI: property: use min() instead of min_t()
PNP: Fix ISAPNP to generate uevents to auto-load modules
ACPI: property: Fix fwnode refcount leak in acpi_fwnode_graph_parse_endpoint()
ACPI: DPTF: Use ACPI_FREE() for ACPI buffer deallocation
ACPI: processor: idle: Drop redundant C-state count checks
ACPI: thermal: Add WQ_PERCPU to alloc_workqueue() users
ACPI: OSL: Add WQ_PERCPU to alloc_workqueue() users
ACPI: EC: Add WQ_PERCPU to alloc_workqueue() users
ACPI: OSL: replace use of system_wq with system_percpu_wq
ACPI: scan: replace use of system_unbound_wq with system_dfl_wq
ACPI: fan: Add support for Microsoft fan extensions
ACPI: fan: Add hwmon notification support
ACPI: fan: Add basic notification support
ACPI: TAD: Improve runtime PM using guard macros
ACPI: TAD: Rearrange runtime PM operations in acpi_tad_remove()
...
Linus Torvalds [Wed, 3 Dec 2025 01:03:55 +0000 (17:03 -0800)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"These are the arm64 updates for 6.19.
The biggest part is the Arm MPAM driver under drivers/resctrl/.
There's a patch touching mm/ to handle spurious faults for huge pmd
(similar to the pte version). The corresponding arm64 part allows us
to avoid the TLB maintenance if a (huge) page is reused after a write
fault. There's EFI refactoring to allow runtime services with
preemption enabled and the rest is the usual perf/PMU updates and
several cleanups/typos.
Summary:
Core features:
- Basic Arm MPAM (Memory system resource Partitioning And Monitoring)
driver under drivers/resctrl/ which makes use of the fs/rectrl/ API
Perf and PMU:
- Avoid cycle counter on multi-threaded CPUs
- Extend CSPMU device probing and add additional filtering support
for NVIDIA implementations
- Add support for the PMUs on the NoC S3 interconnect
- Add additional compatible strings for new Cortex and C1 CPUs
- Add support for data source filtering to the SPE driver
- Add support for i.MX8QM and "DB" PMU in the imx PMU driver
Memory managemennt:
- Avoid broadcast TLBI if page reused in write fault
- Elide TLB invalidation if the old PTE was not valid
- Drop redundant cpu_set_*_tcr_t0sz() macros
- Propagate pgtable_alloc() errors outside of __create_pgd_mapping()
- Propagate return value from __change_memory_common()
ACPI and EFI:
- Call EFI runtime services without disabling preemption
- Remove unused ACPI function
Miscellaneous:
- ptrace support to disable streaming on SME-only systems
- Improve sysreg generation to include a 'Prefix' descriptor
- Replace __ASSEMBLY__ with __ASSEMBLER__
- Align register dumps in the kselftest zt-test
- Remove some no longer used macros/functions
- Various spelling corrections"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (94 commits)
arm64/mm: Document why linear map split failure upon vm_reset_perms is not problematic
arm64/pageattr: Propagate return value from __change_memory_common
arm64/sysreg: Remove unused define ARM64_FEATURE_FIELD_BITS
KVM: arm64: selftests: Consider all 7 possible levels of cache
KVM: arm64: selftests: Remove ARM64_FEATURE_FIELD_BITS and its last user
arm64: atomics: lse: Remove unused parameters from ATOMIC_FETCH_OP_AND macros
Documentation/arm64: Fix the typo of register names
ACPI: GTDT: Get rid of acpi_arch_timer_mem_init()
perf: arm_spe: Add support for filtering on data source
perf: Add perf_event_attr::config4
perf/imx_ddr: Add support for PMU in DB (system interconnects)
perf/imx_ddr: Get and enable optional clks
perf/imx_ddr: Move ida_alloc() from ddr_perf_init() to ddr_perf_probe()
dt-bindings: perf: fsl-imx-ddr: Add compatible string for i.MX8QM, i.MX8QXP and i.MX8DXL
arm64: remove duplicate ARCH_HAS_MEM_ENCRYPT
arm64: mm: use untagged address to calculate page index
MAINTAINERS: new entry for MPAM Driver
arm_mpam: Add kunit tests for props_mismatch()
arm_mpam: Add kunit test for bitmap reset
arm_mpam: Add helper to reset saved mbwu state
...
gentwo / linux / .git / log