Teresa Remmet [Tue, 18 Feb 2025 07:41:52 +0000 (08:41 +0100)]
arm64: dts: imx8mm-phyboard-polis: Add support for PEB-AV-10
PEB-AV-10 is an Audio/Video extension module which extends
phyBOARD-Polis i.MX8MM.
With MIPI DSI to LVDS bridge already populated on SoM the PEB-AV-10 adds
support for:
- connecting 10" display,
- audio with TLV320AIC and
- EEPROM.
arm64: dts: imx8mm-phyboard-polis: Assign missing regulator for bluetooth
Assign the missing regulator to the bluetooth node. Absence of
this regulator triggers the warning message from kernel as driver
uses a fallback dummy regulator when there is no regulator assigned.
arm64: dts: imx8mm-phycore-som: Assign regulator for dsi to lvds bridge
Add a missing voltage regulator of 1.8v to the sn65dsi83
(dsi_lvds bridge) node. Due to the absence of this regulator, a fallback
dummy regulator is used and that triggers a warning message from the
kernel. Assigning the appropriate regulator avoids the warning.
Remove device tree property "fsl,magic-packet" as WoL is not working
on the SoM and so not required. This also saves a significant amount of
power during suspend as the ethernet phy is not powered down otherwise.
Andrej Picej [Tue, 18 Feb 2025 07:41:43 +0000 (08:41 +0100)]
arm64: dts: imx8mm-phycore-som: Fix bluetooth wakeup source
Not using pull-up on the host wake-up line triggers the wake up
immediately after device enters suspend. Fix this by enabling internal
pull-up and setting interrupt triggering on the falling edge.
arm64: dts: freescale: imx8mm-verdin-dahlia: add Microphone Jack to sound card
The simple-audio-card's microphone widget currently connects to the
headphone jack. Routing the microphone input to the microphone jack
allows for independent operation of the microphone and headphones.
This resolves the following boot-time kernel log message, which
indicated a conflict when the microphone and headphone functions were
not separated:
debugfs: File 'Headphone Jack' in directory 'dapm' already present!
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Cc: <stable@vger.kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: freescale: imx8mp-verdin-dahlia: add Microphone Jack to sound card
The simple-audio-card's microphone widget currently connects to the
headphone jack. Routing the microphone input to the microphone jack
allows for independent operation of the microphone and headphones.
This resolves the following boot-time kernel log message, which
indicated a conflict when the microphone and headphone functions were
not separated:
debugfs: File 'Headphone Jack' in directory 'dapm' already present!
arm64: dts: freescale: imx8mm-verdin: Remove LVDS panel and backlight
Remove LVDS panel and backlight nodes from the Verdin iMX8M Mini SoM
dtsi file, those two hardware components are not part of the SoM,
therefore they should not be present in this file.
This is solving a dtb checker warning about panel-lvds compatible.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Fri, 14 Feb 2025 08:47:51 +0000 (16:47 +0800)]
soc: imx8m: Unregister cpufreq and soc dev in cleanup path
Unregister the cpufreq device and soc device when resource unwinding,
otherwise there will be warning when do removing test:
sysfs: cannot create duplicate filename '/devices/platform/imx-cpufreq-dt'
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.13.0-rc1-next-20241204
Hardware name: NXP i.MX8MPlus EVK board (DT)
Fixes: 9cc832d37799 ("soc: imx8m: Probe the SoC driver as platform driver") Cc: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Mon, 3 Feb 2025 17:30:20 +0000 (14:30 -0300)]
ARM: dts: imx28-sps1: Fix GPIO LEDs description
According to leds-gpio.yaml, the LED nodes should not contain
unit addresses. Remove them.
Also, 'default-trigger' is not a valid property. Change it to
'linux,default-trigger'.
These changes fix the following dt-schema warnings:
led@1: Unevaluated properties are not allowed ('reg' was unexpected)
led@2: Unevaluated properties are not allowed ('reg' was unexpected)
led@3: Unevaluated properties are not allowed ('default-trigger', 'reg' were unexpected)
leds: '#address-cells', '#size-cells' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fabio Estevam [Mon, 3 Feb 2025 12:05:11 +0000 (09:05 -0300)]
ARM: dts: vf610-bk4: Use the more specific "lwn,bk4-spi"
Currently, the compatible string used for the spidev device is "lwn,bk4",
which is the same as the board compatible string documented at fsl.yaml.
This causes several dt-schema warnings:
make dtbs_check DT_SCHEMA_FILES=fsl.yaml
...
['lwn,bk4'] is too short
'lwn,bk4' is not one of ['tq,imx8dxp-tqma8xdp-mba8xx']
'lwn,bk4' is not one of ['tq,imx8qxp-tqma8xqp-mba8xx']
'lwn,bk4' is not one of ['armadeus,imx1-apf9328', 'fsl,imx1ads']
Use a more specific "lwn,bk4-spi" compatible string to fix the problem.
Markus Niebel [Mon, 20 Jan 2025 13:25:00 +0000 (14:25 +0100)]
ARM: dts: mba6ul: change sound card model name
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Markus Niebel [Mon, 20 Jan 2025 13:24:59 +0000 (14:24 +0100)]
ARM: dts: imx7-mba7: change sound card model name
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Markus Niebel [Mon, 20 Jan 2025 13:24:58 +0000 (14:24 +0100)]
ARM: dts: imx6qdl-mba6: change sound card model name
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, HDMI audio cannot play sound at a 44.1 kHz sample rate due to
a clock frequency mismatch. This update resolves the issue by allowing
the sai driver to change the clock parent to AUDIO_PLL_1 when the sample
rate is 44.1 kHz. It also ensures that AUDIO_PLL_1 operates at the
correct frequency for this configuration.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ahmad Fatoum [Mon, 13 Jan 2025 22:13:01 +0000 (23:13 +0100)]
MAINTAINERS: match mxc in file names by IMX / MXC entry
There is a number of i.MX-related drivers that have mxc in their name,
but are not matched by the i.MX MAINTAINERS entry, most notably the GPIO
driver, which is still being used on current SoCs.
Looking at current files containing mxc in their name, all of them are
related to i.MX, except for:
arm64: dts: s32g: add common 'S32G-EVB' and 'S32G-RDB' board support
Create common part, s32gxxa-evb.dtsi and s32gxxa-rdb.dtsi, for S32G2/S32G3
RDB2\3 and EVB G2/G3 boards to avoid copy duplicate part in boards dts
file. Prepare to add other modules such as FlexCAN, DSPI easily in the
future.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM: dts: imx6qdl-apalis: Fix poweroff on Apalis iMX6
The current solution for powering off the Apalis iMX6 is not functioning
as intended. To resolve this, it is necessary to power off the
vgen2_reg, which will also set the POWER_ENABLE_MOCI signal to a low
state. This ensures the carrier board is properly informed to initiate
its power-off sequence.
The new solution uses the regulator-poweroff driver, which will power
off the regulator during a system shutdown.
Cc: <stable@vger.kernel.org> Fixes: 4eb56e26f92e ("ARM: dts: imx6q-apalis: Command pmic to standby for poweroff") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In mainboard schematics ENET1 is eqos and ENET2 is fec.
This is reversed to standard aliases using base addresses for ordering.
Adjust aliases for all mainboards accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Tue, 7 Jan 2025 09:49:41 +0000 (10:49 +0100)]
ARM: dts: imx7s: Move csi-mux to below root
fsl,imx-iomuxc-gpr.yaml only contains the mux-controller but the actual
video-mux is not part of it. So move it below root node.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: iomuxc-gpr@30340000: 'csi-mux' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/imx/fsl,imx-iomuxc-gpr.yaml#
The main 24V regulator will toggle GPIO4_IO23 to signal imminent voltage
loss. Reflect this in the DT, so the OS can take appropriate action when
this happens.
Back when this device tree was first added, there were no i.MX8MP
HDMI bindings upstream yet. This has changed now, so let's use them
to describe the HDMI on the imx8mp-skov-revb-hdmi board.
Ahmad Fatoum [Mon, 6 Jan 2025 16:06:38 +0000 (17:06 +0100)]
arm64: dts: imx8mp-skov: use I2C5 for DDC
The HDMI DDC pads can be muxed either to an i.MX I2C controller or
to a limited I2C controller within the Designware HDMI bridge.
So far, the pads were muxed to the HDMI bridge, but the i.MX I2C controller
is the better choice:
- The Designware HDMI I2C controller doesn't support multi-byte
requests and the Linux driver refuses[1] transfers to/from address
0x37, but these are required for display/brightness configuration,
- The driver doesn't support I2C bus recovery, but some HDMI panels used
with the board can be flaky and require it.
As the i.MX I2C controller and driver don't have either of these
limitations, let's make use of it instead.
Ahmad Fatoum [Mon, 6 Jan 2025 16:06:37 +0000 (17:06 +0100)]
arm64: dts: imx8mp-skov: operate CPU at 850 mV by default
The Skov i.MX8MP boards are passively cooled and heatsink is specced for
continuous operation at 1.2 GHz only. Short bouts of 1.6 GHz are ok,
but these should be invoked intentionally, not as part of
suspend/resume cycles.
Therefore, configure RUN frequency as 850 mV and remove the higher
voltage operating points from those permissible for suspend.
Fixes: 6d382d51d979 ("arm64: dts: freescale: Add SKOV IMX8MP CPU revB board") Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PMIC voltage constraints in the device tree currently describe the
permissible range of the PMIC. This is unnecessary as this information
already exists in the driver and wrong as it doesn't account for
board-specific constraints, e.g. a 2.1V on VDD_SOC would fry the SoC and
a maximum voltage of 3.4V on the VDD_3V3 rail may be unexpected across
the board.
Fix this by adjusting constraints to reflect the board limits.
Fixes: 6d382d51d979 ("arm64: dts: freescale: Add SKOV IMX8MP CPU revB board") Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Joe Hattori [Tue, 24 Dec 2024 03:34:56 +0000 (12:34 +0900)]
firmware: imx-scu: fix OF node leak in .probe()
imx_scu_probe() calls of_parse_phandle_with_args(), but does not
release the OF node reference obtained by it. Add a of_node_put() call
after done with the node.
Fixes: f25a066d1a07 ("firmware: imx-scu: Support one TX and one RX") Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Wed, 18 Dec 2024 15:27:32 +0000 (16:27 +0100)]
arm64: dts: imx8mp-kontron: Add support for reading SD_VSEL signal
This fixes the LDO5 regulator handling of the pca9450 driver by
taking the status of the SD_VSEL into account to determine which
configuration register is used for the voltage setting.
Even without this change there is no functional issue, as the code
for switching the voltage in sdhci.c currently switches both, the
VSELECT/SD_VSEL signal and the regulator voltage at the same time
and doesn't run into an invalid corner case.
We should still make sure, that we always use the correct register
when controlling the regulator. At least in U-Boot this fixes an
actual bug where the wrong IO voltage is used and it makes sure
that the correct voltage can be read from sysfs.
Frieder Schrempf [Wed, 18 Dec 2024 15:27:31 +0000 (16:27 +0100)]
arm64: dts: imx93-kontron: Fix SD card IO voltage control
The OSM-S i.MX93 SoM doesn't have the VSELECT signal of the USDHC
controller connected to the PMICs SD_VSEL input. Instead SD_VSEL
is hardwired to low level. Let the driver know this in order to
use the proper register for reading and writing the voltage level.
This fixes SD card access with the latest hardware revision of
the Kontron OSM-S i.MX93 SoM.
Frieder Schrempf [Wed, 18 Dec 2024 15:27:30 +0000 (16:27 +0100)]
arm64: dts: imx8mm-kontron: Add support for reading SD_VSEL signal
This fixes the LDO5 regulator handling of the pca9450 driver by
taking the status of the SD_VSEL into account to determine which
configuration register is used for the voltage setting.
Even without this change there is no functional issue, as the code
for switching the voltage in sdhci.c currently switches both, the
VSELECT/SD_VSEL signal and the regulator voltage at the same time
and doesn't run into an invalid corner case.
We should still make sure, that we always use the correct register
when controlling the regulator. At least in U-Boot this fixes an
actual bug where the wrong IO voltage is used and it makes sure
that the correct voltage can be read from sysfs.
Lukasz Majewski [Thu, 7 Nov 2024 08:57:05 +0000 (09:57 +0100)]
ARM: dts: mxs: Add descriptions for imx287 based btt3-[012] devices
The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to
some extend similar to already upstreamed XEA devices, hence are
using common imx28-lwe.dtsi file.
New, imx28-btt3.dtsi has been added to embrace common DTS
properties for different HW revisions for this device.
As a result - changes introduced in imx28-btt3-[012].dts are
minimal.
Frank Li [Wed, 23 Oct 2024 22:02:52 +0000 (18:02 -0400)]
arm64: dts: imx8mq-librem5: remove undocument property 'extcon' for usb-pd@3f
Remove undocment property 'extcon' for usb-pd@3f to fix below CHECK_DTBS
warnings:
arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dtb: usb-pd@3f: 'extcon' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/ti,tps6598x.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 2 Feb 2025 18:49:13 +0000 (10:49 -0800)]
Merge tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Linus Torvalds [Sun, 2 Feb 2025 18:40:27 +0000 (10:40 -0800)]
Merge tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Len Brown [Sun, 2 Feb 2025 16:43:02 +0000 (10:43 -0600)]
tools/power turbostat: version 2025.02.02
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Linus Torvalds [Sat, 1 Feb 2025 23:07:56 +0000 (15:07 -0800)]
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
Linus Torvalds [Sat, 1 Feb 2025 19:30:41 +0000 (11:30 -0800)]
Merge tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Linus Torvalds [Sat, 1 Feb 2025 18:04:29 +0000 (10:04 -0800)]
Merge tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
Linus Torvalds [Sat, 1 Feb 2025 17:49:20 +0000 (09:49 -0800)]
Merge tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Linus Torvalds [Sat, 1 Feb 2025 17:15:01 +0000 (09:15 -0800)]
Merge tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
Update .mailmap to reflect my new (and final) primary email address,
carlos.bilbao@kernel.org. Also update contact information in files
Documentation/translations/sp_SP/index.rst and MAINTAINERS.
Link: https://lkml.kernel.org/r/20250130012248.1196208-1-carlos.bilbao@kernel.org Signed-off-by: Carlos Bilbao <carlos.bilbao@kernel.org> Cc: Carlos Bilbao <bilbao@vt.edu> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Mattew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
gather_bootmem_prealloc() assumes the start nid as 0 and size as
num_node_state(N_MEMORY). That means in case if memory attached numa
nodes are interleaved, then gather_bootmem_prealloc_parallel() will fail
to scan few of these nodes.
Since memory attached numa nodes can be interleaved in any fashion, hence
ensure that the current code checks for all numa node ids
(.size = nr_node_ids). Let's still keep max_threads as N_MEMORY, so that
it can distributes all nr_node_ids among the these many no. threads.
gentwo / linux / .git / log